I'm using Dell 1600n on home network. In order to use the provided sofware, I try to attach the printer with USB cable as well. My question: can the local (with USB) coexist with Ethernet network?
Is there any conflict between these 2 connections?
I'm not sure what the official answer is, but our 1600n will not work with both the USB and the network connected at once.
In practice, I don't think there are any facilities available via the USB connection which are not also available over the network, so it doesn't really matter.
The reason I asked for using both USB and network connection is because I want to fax or scan from computer, which is not supported by network (I can only do the scanning on the printer). I called Dell tech support the other day. At first he said it would be OK, but later conformed that the two connections would cause conflict.
I thought you can scan from computer but not fax (with usb or network), 1600n has a standalone fax. For the 2 connection why not i think it wouldn't be optimal for spooler gestion butnot sure try it :smileyhappy:
I just installed my 1600n. Everything seems to be ok except I cannot scan anything??? Whenever I try to scan, I am asked to "Select a user ID"??? I am not sure what that is or where I find it? Then, I am notified after a couple of seconds that the "ID list is empty."
My printer is working fine both from the desktop and the networked laptops on our wireless network. I just can't figure out this scanning problem? F.Y.I.- My printer is connected to my desktop (and laptops) via a wireless network (Linksys Wireless Router). Thus, I am not using a USB Cable. I was told I didn't need one. Is this also true?
I've had the 1600n for about a year now, and here's what I know about printing and scanning over a network:
It will scan over the network if you upgrade the firmware and do a lot of tweaking (adding usernames, etc.). However, it's not really worth it b/c the quality of network scan is fixed very low and you end up pressing a lot of buttons every time just to scan something.
I have it hooked up via usb to one computer to do the scanning and via ethernet (linksys router) for several other computers to print only. For a while, the printer would not join the network when powered on, but it might have been a flaky cable or hub problem. It seems to work now.
The scan button on the console is virtually worthless since you can only go 1 page at a time through the ADF; you have to use the paperport app to really make any use of scanning. It's still a multi-step process, but it works pretty good.
Overall opinion: yeah, it has all the parts: copier, scanner, fax, printer, network card, but they don't really work the way you would imagine. It's decent at each function, but not stellar. It really is a 4-in-1 in that you feel like you're supporting four machines at once, each with its own quirks.
What I don't understand is that if it has all the parts that you need to do all these functions, why can't it do them right? Some on the forum have said that you can get an HP that will fax and scan correctly over the network, or 1-touch email a scanned multipage doc from the ADF. So what's missing from the 1600n that prevents it from doing this? It has the parts; must be some software, drivers, or special chips?? The cynical part of me says they don't want to kill the market for the $1000 printer that will do this stuff with a little $200 SOHO job.
I can't really complain too much since I got it for $200 shipped and it came with Paperport 9 which at the time, it was the only MFP that did (the others shipped with v8 which didn't do pdf).
I must respectfully disagree with a few of your comments regarding the 1600n and network scanning. What I think is going on here is perhaps you have not installed the "Dell Network Scan Manager"? It's the key to getting the Net Scan features running properly, but not well-documented.
It's in the 1600n\NetScan folder within the latest driver download, and it's actually a separate little program that runs in the system tray. I had to manually navigate to that folder and run the Setup.exe from there.
During setup of this program, you will be prompted to find the scanner on the network and enter an ID. I just used my initials. For the PIN, you can leave it blank. You'll receive a warning/confirmation that you are leaving it blank, but it's fine.
Once installed, navigate to the Start-Programs-Dell-Network Scan Icon to get it started. Inside you can you can select type of file (pdf, jpeg, etc) and resolution. Your pdf scans are limited to 300dpi using the network, but that's been more than sufficient for the 2000 or so pages that I've scanned. Probably not for photos, but nearly everything else. A little icon will sit in your system tray where you can quickly change things if needed.
Moreover, I AM able to use the ADF over the network and when you switch the default scan to a 300dpi (or other rez)
PDF, it will scan approximately 20-30 pages per minute this way.
To scan quickly, just place your 20 or 30 sheets in the ADF, and on the control panel hit Scan button...then you'll be prompted 3 more times for your userid, pin, etc. However, you can literally hit Scan...Select...Select...Select...as fast as you fingers will let you and it will begin scanning if you did what I said above with the nulled out PIN code. The pin codes are great if you have a lot of people using it or need to chargeback clients. However, I have yet to figure out how compile the scanning stats per UserID/PIN with the computer. I believe you can somehow print a report from the control panel however.
When it's done, it'll ask you if you have more pages. You have to click the Select button on the panel, or it'll wait 30 seconds or so for your answer before the doc opens on your PC. But you can press the Select button immediately upon the MFP prompting for additional pages and your scan will open instantly from within Acrobat or Reader.
P.S. I haven't been able to get the ethernet connector and the USB connector to play nicely together.
P.S.S. You DO need to upgrade to all of the latest firmware.
Hope this is helpful. I only wrote it because it took me months to figure out all this and I personally feel the documentation is extremely poor...and I am a computer guy. Hope I haven't offended.
I did the same on my 1600 and it has been working fine in the past year. The only complaint I have is that the network scanning can't use Dell's scan center. Actually the installation won't install PaperPort unless you have a "local" installation via USB. Also, I noticed that the local scan via USB is very slow compared with network scan via Ethernet (20 seconds per page vs 3-5 seconds). Since I care more about scan speed, I ended up using Ethernet and gave up PaperPort.
Thank you for passing along the result of your months of pain.
Once I got the name of teh program "Network Scan Manager" from a user who WAS able to scan, I found your article and I zeroed in on the installer within moments.
You saved me substantial time. Thank you for passing on knowledge.
My absolute pleasure! Although it's been nearly a year since I posted this, it remains applicable. Just yesterday I had to go through the process again when updating drivers. Amazing. I honestly think Dell could condense the entire user's manual to about 10 pages or less if they would focus on the tasks attempting to be carried out.
Section I: I want to scan to my local computer only and user Paperport
Section II: I want 2 or more users to have scan access over a LAN
Section III: I want to print only
Section IV: You get the drift
Again, glad to be of help and please post with additional questions, like how to have the scanner default to 300dpi B&W PDF scans!
This crime is not Dell's alone. Technical writing is an art form few companies wish to pay for. The manuals are written by secretaries translating programmerese to English. It comes off as readable, but gets lost in minutae ill-described. If those 10 page manuals were available the entire "Dummies" series would never have been necessary.
jhs51
6 Posts
699
0
Posted November 23rd, 2005 15:00
I'm not sure what the official answer is, but our 1600n will not work with both the USB and the network connected at once.
In practice, I don't think there are any facilities available via the USB connection which are not also available over the network, so it doesn't really matter.