UNSOLVED

mpyusko

updated

8 months ago

M

mpyusko

1 Rookie

•

9 Posts

0

1451

October 27th, 2022 07:00

T7910 TPM 2.0 upgrade not working. TPM not detected after flash.

Previously I have TPM 1.2 and it was running fine.  I downloaded the Dell TPM 2.0 upgrade from the proper list for my workstation.  I followed the instructions, it rebooted the computer and then flashed the TPM.  It said the upgrade was successful.  When Windows 10 came back it told me "Standard Hardware Security not supported" in the Device Security.  I rebooted into the BIOS and it still indicated TPM1.2 under "Security" was enabled (A34).  I turned it off.  Rebooted.  Same Error from Windows.  Rebooted, and turned it Back on again.  Same error in Windows.  The TPM Flash utility cannot find the device.  It's like it completely disappeared.  I tried to reflash my BIOS to A34 and it won't do it.  No I don't have TPM at all on this workstation.

Ideas?

  • mpyusko

    1 Rookie

    •

    9 Posts

    624

    0

    Posted October 27th, 2022 07:00

    mpyusko_0-1666881842189.png


    PPI is enable for both in my BIOS, the TPM is On, TPM is Enabled.  (Everyhing except "clear" is checked.)

  • Chino de Oro

    11 Legend

    •

    8554 Posts

    •

    47161 Points

    614

    0

    Posted October 27th, 2022 11:00

    Did you enable TPM auto-provisioning afterward?  Using PowerShell and type the command "get-tpm" to check the status.

    Sometimes, a system hard reset can bring the TPM function back.

  • mpyusko

    1 Rookie

    •

    9 Posts

    600

    0

    Posted October 28th, 2022 06:00

    mpyusko_0-1666964272859.png

     

  • Chino de Oro

    11 Legend

    •

    8554 Posts

    •

    47161 Points

    575

    1

    Posted October 28th, 2022 20:00

    Be sure to have all your data back up and perform a reset using CMOS jumper.  System will restart several times.  Get into BIOS settings to check TPM status.

  • 521

    0

    Posted November 14th, 2022 12:00

    How about an update on your results sir? I have the very same issue on 2 ea. T7910.

     

  • 513

    0

    Posted November 14th, 2022 19:00

    I spent most of the day today focused on upgrading to W11, even though my dual processors are not inline with what MS says they support for W11, but I am good with that. I tried alot of things to get my TPM to be seen by W11 and the very same issues the OP had, I had, so read up if you want those details.

     

    I followed Chino De Oro's suggestion and I reset the bios by using a jumper to do the hard work. After that, BOOM, TPM 2.0 was already to go! A little registry hack that MS details how to use and W11 was installed and operating fine.

     

    Thanks Chino!

  • Chino de Oro

    11 Legend

    •

    8554 Posts

    •

    47161 Points

    496

    0

    Posted November 16th, 2022 07:00

    You' re certainly welcome.  I'm glad it worked for you.

  • Miggarti

    1 Rookie

    •

    11 Posts

    483

    0

    Posted November 17th, 2022 14:00

    I see the Secure Boot State show "off" in page of MSINFO32 ! To install Windows we need make sure the settings in the BIOS about security features are all set to enable.

  • coxbuell

    1 Rookie

    •

    1 Message

    1

    0

    Posted March 23rd, 2026 14:52

    Thanks, I get TPM 2.0 with your help.

    Thanks again.

    NC