tuccero9

updated

3 months ago

T

tuccero9

2 Intern

•

11 Posts

0

1095

February 19th, 2026 06:46

PowerEdge TPM Module update fails

Hello,

We have Poweredge R760 and Poweredge R660xs servers in our infrastructure and all of them are connected to our on-premise OpenManage Enterprise appliance.

From the compliance report i noticed that there is a TPM Module update available (from version 7.2.3.1 to version 7.2.4.1).

However, this specific update fails on all servers when attempting to do it via OME.

I attempted to update the firmware manually but it gives me the following error:
"This DUP requires TPM bootloader version 2.0.0.26 or earlier. Version 2.0.0.32 found.\nparts 948W4, 151Y6, 0PTVP, T2FR2, and VR2WC are supported. Parts T9CVK and K6K71 require the other DUP"

Note that the majority of servers are running ESXi version 8.0.3 and few of them are Windows Server 2025.

The error that i mentioned above was returned from a windows server.

I searched online and i found many other cases of people facing the same issue but i was not able to find a solution to that.

Can you please advise?

  • Dell-Martin S

    Moderator

    •

    3883 Posts

    •

    25810 Points

    0

    1

    Posted February 19th, 2026 14:22

    Hi,

    you could check your service TAG too for part numbers on our Website.

     

    But you could try the steps that I wrote earlier without checking it, because it seems to be the other modules.

    For providing such information it would be better to do this not in an open for everyone contact method.

     

    with kind regards Martin/ Liebe Grüße Martin

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

    DELL-Martin S

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell


  • Dell-Martin S

    Moderator

    •

    3883 Posts

    •

    25810 Points

    0

    1

    Posted February 19th, 2026 12:27

    Hi,

     

    This could happen if you have other TPM part number installed.

     

    How to fix it

     

    Identify the TPM part in iDRAC

    On any affected R760 / R660xs:Open iDRAC → Hardware → Inventory → Security (or similar) and note the TPM part number (you’ll see something like T9CVK, K6K71, 151Y6, 948W4, etc.).

     

     You can also export the inventory via iDRAC/OME to confirm this at scale. 

    Match the correct TPM 7.2.4.1 DUPUse Dell’s support pages for your exact server model, but in general for 15G/16G PE:

    Update manually on one test hostFor a Windows Server 2025 host (no BitLocker or with BitLocker suspended):Download the correct DUP (2XHC3 or 256M6) for R760/R660xs from Dell Support. 

    Run the .exe in Windows (elevated), follow prompts, then reboot when prompted.Verify in iDRAC: TPM firmware shows 7.2.4.1 and compliance clears for that host.For ESXi hosts you can either:Use Lifecycle Controller (F10) with the correct DUPs on a USB / network share. 

    Or mount the DUP via a live OS that supports the package, if Dell documents that method for these specific DUPs.Fix it in OpenManage EnterpriseOME’s catalog is almost certainly pointing one generic TPM update (e.g., 2XHC3) at all R760/R660xs, even the ones with T9CVK/K6K71. That makes compliance show “update needed” and the job then fails. 

     

    To resolve:Import both TPM DUPs into your OME / repository (2XHC3 and 256M6). 

    If possible, create two custom baselines:Baseline A with 2XHC3 for systems whose TPM inventory shows 948W4/151Y6/0PTVP/T2FR2/VR2WC.Baseline B with 256M6 for systems whose TPM inventory shows T9CVK/K6K71.Assign baselines accordingly (using device groups or filters based on a naming/tagging convention linked to TPM type).If OME can’t distinguish TPM part in rules, you may need to:Leave the generic catalog as-is but exclude TPM from global compliance, and handle TPM via dedicated baselines/groups; orAccept that OME will show “non‑compliant” but run the correct DUP manually or via an out‑of‑band job targeted only at the right subset of hosts.

    with kind regards Martin/ Liebe Grüße Martin

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

    DELL-Martin S

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell


  • tuccero9

    2 Intern

    •

    11 Posts

    0

    0

    Posted February 19th, 2026 13:01

    @Dell-Martin S​ 

    Thank you for your reply.

    I cannot detect the TPM part number.

    From iDRAC9 (firmware version 7.20.80.50) i find the following information under Configuration -> BIOS Settings -> System Security

    OffOn
    EnabledDisabledClear
    YesNo
    Current Value Pending Value
    DisabledEnabled
    DisabledEnabled
    SHA1SHA256SHA384

    I also used the command "racadm hwinventory" from cli but i did not found any reference to "tpm part number"

    I exported the hardware inventory from iDRAC as well but still no reference to tpm part number.

    You can find the exported xml attached as well.

  • tuccero9

    2 Intern

    •

    11 Posts

    0

    0

    Posted February 19th, 2026 13:04

    Sorry it seems that there is no option to attach a file apart from images and video

  • tuccero9

    2 Intern

    •

    11 Posts

    0

    0

    Posted February 20th, 2026 08:40

    @Dell-Martin S​ 

    Hello,

    Thank you for you prompt replies and feedback.

    I manage to update the R660xs servers.

    Like you mentioned in your last post i found the service tag of the servers and from Dell Support site i used it to identify the correct package for the update.

    Then from the server's iDRAC i uploaded the package.

    I will use this method for all because it will be the same procedure for all servers irrespective installed OS

  • Dell-Martin S

    Moderator

    •

    3883 Posts

    •

    25810 Points

    0

    0

    Posted February 20th, 2026 13:01

    Thank you for your feedback here 

    with kind regards Martin/ Liebe Grüße Martin

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

    DELL-Martin S

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell