PowerEdge T320 can't find recognize SATA drives after power outage
I know this server is long out of support but I'm hoping the problem pattern matches to something someone recognizes.
A couple of unfortunate events led to this problem (aside from not upgrading the server in way too long).
1) I didn't make a copy of all my bios settings after recieving the machine many many years ago, so I don't know if any of the settings are different than factory default.
2) I didn't notice the error message about the system board battery failing (CMOS battery)
3) Lost power
So now the BIOS has reset, and the server won't boot. When I go into the BIOS, the SATA is settings are set to AHCI. All of the hard drives are in the hard drive backplane.
When I go into the system BIOS, all of the SATA ports (Ports A through F) are listed as "Unknown"/"Unknown Device" except for the optical disk (Port E). I know that the server was initially purchased with only 1 hard drive.
If I remove one of the drives and check it on another device, the drive (and the data) can be read fine, so the drives are working.
What BIOS setting could be preventing it from seeing them properly? Should I switch it the onboard to "RAID"? (That gives me the scary data loss warning).
The first thing I would start with is to take the server to its minimum to post configuration, which is removing everything from the server internally and externally, except for the following;
System Board
CPU1 with heat sink (minimum for troubleshooting)
Single DIMM configuration with DIMM in socket A1
Control Panel with cable (to power system on)
PSU (and for redundant PSU also the PDB/PIB)
Try powering up under that configuration, if the server still fails to post then it is one of the devices above that is causing the issue. Before replacing anything you may check each are seated correctly.
Now if the server does post after taking to a minimum to post, then you will want to power back down and then individually add the removed devices back, until one causes the issue to reappear, identifying the part that had failed.
Thanks for your reply. In this case the device POSTs fine, it just fails to find a bootable hard drive during the boot sequence, and the bios doesn't list the drives. If I go into the configuration for the raid controller using control+r, I do see the disks there and all of them are list as Non Raid.
None of the hard drives were raided together through the raid controller (two were striped under windows, but that was controlled by windows server).
The raid controller looks like it has two large bundles of cable connected to the backplane, labeled Ctrl SAS A and B.
Unfortunately I dont know how the original bios was configured for onboard SATA (ahcp, ata, or raid). Is it possible the bios was configured to Raid, but all of the drives were non raid?
In that case would you confirm how the server raid was configured previously, as well as the controller installed? Also, you may need to upload a TSR from the server, to help identify what happened, and the best way to resolve.
DELL-Chris H
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!
one other note: when the server was originally configured and delivered, it had only one hard drive. i have just confirmed that if I remove that hard drive it is readable by another machine, so that boot drive was non-raid.
the other hard drives in the system were all added after the initial installation of the system and were never configured via the RAID controller, so they would have whatever default configuration would be.
There isn't a default configuration per se, it would be however it was configured as. What I would suggest is that you run a TSR, as laid out here. Once complete then upload it to upload . dell. com and then private message .Dell-Dheeraj the svc tag you used to upload it in order to locate it.
I ask this as it will likely require us understanding exactly how it was configured, and failed, in order to mitigate the chances of data loss.
DELL-Chris H
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!
Thanks for your reply. In trying to get the TSR, I ended up going through the BIOS settings again and realized the one thing I hadn't tried yet -- changing the boot option from BIOS to UEFI. This recognized the boot drive on the raid controller (non-raid) and the system has now started up.
Thank you all for helping me think through this. Now its time to buy a modern poweredge server!
Had this issue, figured out I had to adjust the hard drive in the caddy from the SataU to SAS. .. Lights came on, recognized immediately as NON RAID HD, was able to install an OS and boot ufei with achi setting
Dell-Dheeraj
1 Rookie
•
143 Posts
188
0
Posted December 6th, 2022 01:00
Hi @rlittletht,
The first thing I would start with is to take the server to its minimum to post configuration, which is removing everything from the server internally and externally, except for the following;
Try powering up under that configuration, if the server still fails to post then it is one of the devices above that is causing the issue. Before replacing anything you may check each are seated correctly.
Now if the server does post after taking to a minimum to post, then you will want to power back down and then individually add the removed devices back, until one causes the issue to reappear, identifying the part that had failed.