UNSOLVED

D830wireless

updated

19 years ago

0

15913

July 9th, 2007 09:00

ProWireless 4965AGN / Linksys WRT350 wireless N router only connects in G (54Mbs)

I have a D830 laptop with a 4965AGN with Windows Vista 32 and a Linksys WRT350N
capable of wireless N.
 
I have the latest drivers on both the 4965AGN downloaded 7/7/2007 and the latest on the
Linksys.
 
All attempts at wireless N speed are rejected in favour of G at 54Mbs. There seem to be
a lot of threads on this.
 
I looked at Intels user guide for the 4965AGN and found the following on page 142 :
(see the part about only being supported with security WPA2-AES)
 

802.11n Mode

The 802.11n standard builds upon previous 802.1X standards

by adding multiple-input multiple-output (MIMO). MIMO

increases data throughput to improve transfer rate. Select

Enabled

or Disabled to set the 802.11n mode of the adapter.

Enabled is the default setting.

NOTE

: This setting is available only if the adapter is an Intel

(R) Wireless WiFi Link 4965AGN.

NOTE: To achieve transfer rates greater than 54 Mbps on

802.11n connections, WPA2-AES security must be selected. No

security (None) can be selected to enable network setup and

troubleshooting

 

The Linksys does support WPA2-AES (PSK2 AES) but it still doesn't work

I see also that Intel recommend to switch OFF databurst on the router, I have to try that next ...

Has anyone else experienced this and have a workaround ? I find it

astonishing that these products don't work together , the call to Dell support
has gone very quiet ....

 

 



Message Edited by D830wireless on 07-10-2007 07:00 AM
  • 399

    0

    Posted July 10th, 2007 11:00

    Nir
     
    Thanks for the info. A few point about what you wrote however.
     
    The Linksys is a 2.4 GHZ router , not 5 GHZ. But I found this in the 4965AGN Users Manual :
     

    Your Intel(R) Wireless WiFi Link 4965AGN adapter is compatible with 802.11a, 802.11b,802.11g, and 802.11n wireless standards. Operating at 5 GHz or 2.4 GHz frequency at data rates of up to 300 Mbps, you can now connect your computer to existing high-speed networks that use multiple access points within large or small environments.

    So I don't think that can be the issue. I can also force the Linksys to only operate at Wireless N , and in this case the 4965AGN refuses to connect so I don't think its a question of "displaying" the wrong wireless setting, it really defaults to G.

    I am going to disable the "burst" mode on the router (seems to be an Intel known issue) to see if I can get working. I found this on Intels product information pages .

     

     

  • Nir Nissim

    1 Rookie

    •

    21 Posts

    399

    0

    Posted July 10th, 2007 11:00

    I have had this problem ever since vista was out , allthough I have Dell TM 1500 card , I learned alot about issues with 802.11n , so maybe this will help..
     
    first - intel claims that for 802.11n you will need 3 antennas attached , I hardly believe that you have 3 installed since dell installs only 2 on their laptops (please correct me if im wrong about this) , the claim of intel isn't official , rather posted by a user who said he got this information from intel support about the same issue.
     
    second - microsoft says there is a problem regarding 802.11n , you can look about the following article for more information :
    basiclly they are saying allthough you see you are connected at 802.11g , this is only a "display" issue , the only way you can verify this is by transferring a large file from your lappy wifi to another computer on a LAN, check your speeds (you can use Task Manager , or just calculate).
     
    if you don't have a network , and just using your wireless to connect the internet I suggest you forget about the all thing since most internet providers max at 5-10mbps , thus you will never reach the max speed for 802.11g.
     
    ok now there could be several other reasons for that :
    1. you have a neighbour using 802.11g , thus your router goes into compability mode (802.11g) to avoid interrupting others , seems unlikely cause you have intel card (uses 5Ghz for 802.11n , see next remark) but I though it should be mentioned since this is a problem for many others.
    2. you router doesn't support 5Ghz - intel card supports 802.11n speeds only at 5Ghz , not at 2.4Ghz channels
    3.allthough hard to believe - you have other communication devices on 5Ghz range (maybe home phone ? wireless mouse ? , again hard to believe since 99% use 2.4Ghz , that's why intel restriced 802.11n to 5Ghz spectrom .. well that and other reasons)
    4. driver problems - install the latest firmware for router , get the most updated driver (from intel directly may be the best option)
    5. your intel 4965 adapter setting may be set to 802.11g  , check your settings I won't elaborate on this since I don't know this card personally
     
    there could be more reasons , but let's start at that .
    personally I believe the problem is with your card antennas , you can maybe simply check this by dissasembling the wifi adapter cover , I have an Inspiron 1705 and it's near the battery , check where yours is placed.
     
    for myself I yet havn't got my 802.11n to work , there is a lot of confusion out there regarding the compability with this technology.
     
    hope you would get it to work.
     
    Nir


    Message Edited by Nir Nissim on 07-10-2007 07:08 AM
  • Nir Nissim

    1 Rookie

    •

    21 Posts

    399

    0

    Posted July 10th, 2007 14:00

    well I checked again cause I remembered something about it , and I found out that
    I was wrong , well only half wrong it seems.
     
    according to intel reviewers guide , "channel bonding is best supported at 5Ghz".
    only best supportd , not limited to , I may have conused the two.
     
    anyway if u wanna check this you can look under the following guide under para 2.2.2
     
     
    on the way I also found another answer to the number of the antennas needed , it appears you need two to reach 270mbps , and 3 to reach 300mbps. found this info under the user guide.
    so I learned something new today too 
     
    I surely hope you will get your 802.11n to work properly cause I would buy this card too the minute I hear someone with a dell lappy got it to work with vista.
     
    good luck
  • 399

    0

    Posted July 11th, 2007 03:00

    Nir,
    Thanks for the info. After disabling the frame burst on both sides and configuring
    WPA2-AES it still doesn't want to communicate on N.
     
    The Linksys has two antenna and operates only at 2.4ghz.
     
    Don't know where else to go from here apart from reporting it Intel and Linksys.
  • dgkpcon

    3597 Posts

    399

    0

    Posted July 12th, 2007 19:00

    i dont know what problems your having ,but my 4965agn is and has worked fine and flawlessly.not one problem
  • Nir Nissim

    1 Rookie

    •

    21 Posts

    399

    0

    Posted July 15th, 2007 11:00

    dgkpcon - couple of question if u don't mind :
    by no problems - you mean your card work at 270mbps flawlessly ?
    have you verified this on a network transfer ?
    are you using windows vista ?
    if so what is your router ?