hant0111

updated

2 years ago

H

hant0111

1 Rookie

•

5 Posts

•

2 Points

0

120

November 13th, 2024 20:30

Port Mirroring on Switch Dell EMC N1148T-ON

Hi all,

I am configuring port mirroring for Dell EMC N1148T-ON Switch. Below is the current network model I am using. Currently this Switch is a WAN Switch placed behind Peplink and before the Firewall. This Switch connects to Peplink with 2 uplink ports (port Te1/0/25, Te1/0/26) and is grouped into 1 port-channel (po1). I have configured the monitor session as follows:

Switch(config)# monitor session 1 source interface gi1/0/1
Switch(config)# monitor session 1 source interface gi1/0/2
Switch(config)# monitor session 1 source interface gi1/0/3
Switch(config)# monitor session 1 source interface port-channel 1
Switch(config)# monitor session 1 destination interface gi1/0/31

As the command line above, I have configured the source monitoring interfaces gi1/0/1, gi1/0/2, gi1/0/3 (these are the interfaces connected to the local device), port channel po1 (Te1/0/25 + Te1/0/26) and the output interface connected to the monitoring device is port 13. However, on the monitoring system, I can only see traffic between private IPs (of interfaces gi1/0/1, gi1/0/2, gi1/0/3) but dont see any traffic from public IPs to private IPs through the other 2 uplink ports 25 and 26.

Please explain to me why this happens and how to handle it?

Thanks.

  • DELL-Erman O

    Moderator

    •

    2984 Posts

    •

    14874 Points

    0

    0

    Posted November 14th, 2024 11:21

    Hi, please take a look at these importing things to know:

    • Port Monitoring is supported on both physical and logical interfaces like virtual area network (VLAN) and port-channel.
    • The monitored (the source) and monitoring ports (the destination) must be on the same switch.
    • In general, a monitoring port should have no ip address and no shutdown as the only configuration.  A monitoring port also may not be a member of a VLAN.
    • There may only be one destination port in a monitoring session.
    • A Port monitoring session can have multiple source statements.
    • One Destination Port can be used in multiple sessions.

    DELL-Erman O

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

  • DELL-Joey C

    Moderator

    •

    4170 Posts

    •

    20965 Points

    0

    0

    Posted November 14th, 2024 01:51

    Hi,

     

    Can you do a show tech for the configuration, it's probably a configuration issue. Also, what firmware version are you on?

    DELL-Joey C

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’ if I did. 

  • hant0111

    1 Rookie

    •

    5 Posts

    •

    2 Points

    0

    0

    Posted November 14th, 2024 02:01

    Hi,

    This is configuraion of 2 interfaces Te1/0/25, Te1/0/26 and firmware version.

    Please check for me soon.

    Thanks.

  • DELL-Joey C

    Moderator

    •

    4170 Posts

    •

    20965 Points

    0

    0

    Posted November 14th, 2024 04:09

    Hi,

     

    The pictures are quite in low quality. I think I can roughly see what's the configuration. 

     

    Can you try creating a different session for the port channel group, to separate from the physical group. I think you cannot mix both logical and physical on a single session. 

     

    Try:

     

    Switch(config)# monitor session 2 source interface port-channel 1
    Switch(config)# monitor session 2 destination interface gi1/0/32

    DELL-Joey C

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’ if I did. 

  • hant0111

    1 Rookie

    •

    5 Posts

    •

    2 Points

    0

    0

    Posted November 14th, 2024 08:19

    @DELL-Joey C​ 

    Hi,

    This switch model, DELL EMC N1148T-ON only allow me create one monitor session. I can't create second session for monitoring.

  • DELL-Joey C

    Moderator

    •

    4170 Posts

    •

    20965 Points

    0

    0

    Posted November 14th, 2024 09:45

    Hi,

     

    I do not have the switch model to check on the issue, would you mind issue a command #monitor session ? to see how many sessions can be input. Usually is shown <1-4>

     

    If this is not possible to add more session, could you remove physical interface from the session and only remain the port channel to check if the issue still remain. 

    DELL-Joey C

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’ if I did. 

  • hant0111

    1 Rookie

    •

    5 Posts

    •

    2 Points

    0

    0

    Posted November 14th, 2024 10:23

    @DELL-Joey C​ 

    Hi,

    In picture below, i tried to type #monitor session 0, and the output is "Value is out of range. The valid range is 1 to 1". That means I can only have have 1 session monitored.

  • hant0111

    1 Rookie

    •

    5 Posts

    •

    2 Points

    0

    0

    Posted November 14th, 2024 11:30

    @DELL-Erman O​ 

    Hi,

    Thanks for your reply. My configuration fully satisfies the requirement you gave, however on the monitoring device I only see internal traffic through the GigabitEthernet ports without seeing traffic information on TerabitEthernet ports from outside through the 2 uplink ports on Switch devices connected to Peplink.