UNSOLVED

Corvax1

updated

13 years ago

C

Corvax1

6 Posts

0

1871

September 4th, 2013 10:00

Volume missing from Networker GUI

We have a file server that has 3 Drives with Networker client installed.  Windows 2008 R2 sp1 x64.

C: , E: , F:

When trying to recover from the Networker user, the E:\ is not visible in the GUI.

We see the save sets, the browse period is set to 3 months.  Looking at the save set list, I see the save sets for the drive E:\ and they indicate that they are browsable.

How can I go about and making the save sets visible in my client?

Regards,

  • christopher_ime

    6 Operator

    •

    1962 Posts

    823

    0

    Posted September 4th, 2013 20:00

    Please consider moving this question as-is (no need to recreate) to the proper forum for maximum visibility.  Questions written to the users' own "Discussions" space don't get the same amount of attention and questions can go unanswered for a long time.

    You can do so by selecting "Move" under ACTIONS along the upper-right.  Then search for and select: "Networker Support Forum" which would be the most relevant for this question.

  • ble1

    6 Operator

    •

    14354 Posts

    •

    56186 Points

    826

    0

    Posted September 5th, 2013 09:00

    Could it be that you have separate jobs for backup?  In such case, setting browse time to one indicated by mminfo will make E drive visible.

  • bingo.1

    1 Rookie

    •

    2430 Posts

    826

    0

    Posted September 5th, 2013 09:00

    As we cannot look into your environment,it is not so easy to answer why the E: drive is not visible.

    However, you can use "recover -S ssid -a pathname" (or the appropriate option from the GUI) to recover a (sub-)directory easily.

    A potential cause might also be that this is a cluster where the application/drive has been switched after a failover.

  • Corvax1

    6 Posts

    826

    0

    Posted September 5th, 2013 10:00

    I had 1 job with ALL as backup set.

    this morning, I tried something and created a copy of the client and selected just the E:\ drive for the backup set.  after manualy running the job, the E:\ was visible to the GUI but only with the save set created by the manual job.... This is a wierd behavior IMO.

    Untill I figure it out, I decided to created 3 seperate jobs for this particular client.  sucks, but at least I will be able to do restores...

  • Corvax1

    6 Posts

    826

    0

    Posted September 5th, 2013 10:00

    bingo wrote:

    As we cannot look into your environment,it is not so easy to answer why the E: drive is not visible.

    However, you can use "recover -S ssid -a pathname" (or the appropriate option from the GUI) to recover a (sub-)directory easily.

    A potential cause might also be that this is a cluster where the application/drive has been switched after a failover.

    This is not a cluster, just a standard Virtual Server with Windows 2008 r2.

  • ble1

    6 Operator

    •

    14354 Posts

    •

    56186 Points

    826

    0

    Posted September 5th, 2013 11:00

    I wonder if you can do following:

    a) run from server job for E drive

    b) see if you can see it (I suspect yes)

    c) run nsrim -X

    d) check again

    If you won't see it after step c) this may indicate that index is save wrongly (nested index or some other related issue which usually goes to DNS). However, this would make sense for whole box and not just E drive.  Are you sure E drive is local disk just like D and C?  Actually, there is nice way to verify this.  Go to server and do following:

    nsrinfo > foo.txt

    Load foo.txt to your favorite editor and check what records and from when do you have for E drive (and verify others are there too).  Also, check with mminfo what sumflags and what ssflags you have against drives for this client.

  • Corvax1

    6 Posts

    826

    0

    Posted September 5th, 2013 13:00

    Also, just noticed this.

    Since I ran my job for the E:\ I can browse throught the folders starting today (05/09/2013).  Selecting a folder or a file and going to view versions.  I see all the versions from 27/08/2013 and up, but I can't mark them.  It says to change browse time in order to restore a different version, but If I change browse time the a earlier date, I lose the E:\ and can't browse it anymore... lol 

  • ble1

    6 Operator

    •

    14354 Posts

    •

    56186 Points

    826

    0

    Posted September 5th, 2013 13:00

    Do you see the same thing if you use CLI? What is the version of NW that you run on client and server?

  • Corvax1

    6 Posts

    826

    0

    Posted September 5th, 2013 13:00

    I'm sure these are local disks, no worries there.

    nsrinfo foo.txt shows entries for the E:\ Starting the 28/08/2013 (made a 350 mb file)

    doing the mminfo -c

    I see entries for the drive E:\ and F:\ that start on the 28/08/2013.

    This is normal, the drives were presented to the server on this date.  A Full was ran and 250GB where backup.  There is then entries for incr on each day following that day.

    I'm realy supified, everything seems to be there, the save sets are marked as browsable, the data, etc... It's just not showing in the GUI 

  • Xao1

    16 Posts

    163

    0

    Posted September 12th, 2013 16:00

    Try a saveset recover.