I'm trying to enable the ULT 3582 auto-cleaning but when configuring it came back with no cleaning cell.
I'm not sure whether the NetWorker 76 build 142 for AIX 6.1 is configured correctly or not. Could you help to check if the NSR jukebox and NSR device for rmt0.1 and rmt1.1 are OK? The goal is to let the ULT3582 to do the cleaning. (Not sure if this is better than using the NetWorker).
Your help is apprecaited.
Ren Wong
#nsrjb
1: sdp_nsr [enabled]
There is only one enabled and configured jukebox: sdp_nsr
Jukebox sdp_nsr: (Ready to accept commands)
slot volume pool barcode volume id recyclable
1: CMV007 MainDBbackup CMV007 3535443941 no
2: CMV025 MainDBbackup CMV025 3518666916 no
3: CMV009 MainDBbackup CMV009 3501889859 no
4: CMV004 MainDBbackup CMV004 3485112765 no
5: CMV002 MainDBbackup CMV002 3468335689 no
6: CMV001 MainDBbackup CMV001 3451558802 no
7: CMV003 HistDBbackup CMV003 3434781849 no
8: CMV00H HistDBbackup CMV00H 3418004816 no
9: CMV00C HistDBbackup CMV00C 3401227707 no
10:
11:
12: CMV008 HistDBbackup CMV008 3384450641 no
13:
14:
15: CMV019 HistDBbackup CMV019 3367673594 no
16: CMV005 HistDBbackup CMV005 3350896505 no
17: CMV01G HistDBbackup CMV01G 3334119407 no
18:
19:
20:
21: CMV00F bootstrap CMV00F 4189542823 no
22: Cleaning Tape (46 uses left) CLNI05 CLNI05 -
23: Cleaning Tape (47 uses left) CLNU63 CLNU63 -
*not registered in the NetWorker media data base
drive 1 (/dev/rmt0.1) slot 21: CMV00F (mounted)
Latest Frimware release 2005/7/12
310B.GY005
Driver 73V1
Confirm from IBM site which are the latest
Try to turn off the host autocleaning
nsradmin> print type: NSR jukebox; name:sdp_nsr
type: NSR jukebox;
name: sdp_nsr;
comment: ;
description: "scsidev@2.1.1: Standard SCSI Jukebox";
model: Standard SCSI Jukebox;
enabled: Yes;
control port: scsidev@2.1.1;
devices: /dev/rmt0.1, /dev/rmt1.1;
number devices: 2;
number drives: 2;
SmartMedia update interval: 12;
bar code reader: Yes;
match bar code labels: Yes;
jukebox serial number: ATNN=IBM ULT3582-TL 0000013387791000;
76 build 142??? Come on You must patch that. Normally, when cleaning is configured to be done via library itself (see http://ps-2.kev009.com/rs6000/manuals/Tape/358x/3582/3582_Setup,Operator,Svc_Guide_a67po0ct.pdf) then this won't represented to outside world and you will see only available slots outside that, but this may depend on library too (my experience comes from Quantum lib). If visible, you can lock working range via available slots and disable NetWorker cleaning in NW.
No, auto media management is not related to cleaning in NetWorker. Auto clean should be set to No and available slots should exclude cleaning slots if you see them.
When you look at the properties of the tape library there should be a check mark field to turn on/off auto-cleaning. Next to that there should be a field where you can put in available tape library slots. In your case it looks like that would need to be 1-21
First enable Diagnostic mode on the NMC, to do this to to NMC - > View -> diagnostic mode. once enabled go to the properties of your Jukebox -> Advanced Tab -> Available slots. it should be 1-21 in your case. Disable the library and enable it for the changes to take affect.
If you're not completely familiar with using nsradmin in edit mode to change the jukebox resource as you need to run nsradmin, skip the first part and look at the part of editing the resourcefile directly while networker is down.
For the nsradmin way; do this while first disabling the jukebox to prevent access to the resource!!!
1). the nsradmin way # nsradmin # nsradmin> . type:nsr jukebox;name:put_jukebox_name_here # nsradmin> edit
Then the jukebox resource opens in a vi-like session, available for manual editing.
- change "available slots" parameter - change "physical slots" parameter - for the part "volume ids" delete the slot entries from behind so that there are only desired amount of slots left - for the part "volumes" delete the volume entries from behind so that there are only desired amount of slots left
save and quit
NOTE! When using nsradmin to edit a resource pay attention to the fact that there is 1 space character at the end of each line! Do not forget to have that space at the end of a line when adding/removing lines from a resource file.
2). the editing of the resourcefile while networker is down In stead you could better try to change the jukebox resourcefile while networker is down. The benefit is that you first can copy that file as a fast fallback in case you make an error. With nsradmin you sometimes can get in a stuck situation
Look for the jukebox resourcefile in directory /nsr/res/nsrdb/ (every jukebox has its own resourcefile in NW 7.x)
In this case it's a stk L700 with 678 slots, the resourcefile of which is called 8a1713b63f5b5876a3af2c1b and is in directory 07.
If you want to change the the slots you should: - shutdown networker - edit the resourcefile and change parameters available slots (1-23;) and physical slots (1, 21;) so that it reflects to the situation you want - start networker again
ble1
6 Operator
•
14354 Posts
•
56186 Points
1591
0
Posted July 15th, 2014 12:00
76 build 142??? Come on
You must patch that. Normally, when cleaning is configured to be done via library itself (see http://ps-2.kev009.com/rs6000/manuals/Tape/358x/3582/3582_Setup,Operator,Svc_Guide_a67po0ct.pdf) then this won't represented to outside world and you will see only available slots outside that, but this may depend on library too (my experience comes from Quantum lib). If visible, you can lock working range via available slots and disable NetWorker cleaning in NW.