Based on a lot of things that have been said here there is several things you should check.
1) Zoning is setup proper 2) Switch is hard set for 4gb and not on Auto 3) Are the tape drives in use when you are trying to do this? (belive it or not this matters.)
Inquire although useful, will display different information back to a server connected to the same drives, if those drives are in use on a different server. So make sure none of the hardware is in use.
I myself have tried to setup drives on a storage node in the past, and scratched my head as to why doesn't the server see them, and why arent they appearing in inquire, only to come and find out they were in use.
4) Open your HBA software and see if the drives appear there. If they don't, or only one of them does. You need to go back to the switch. OS won't see them if the HBA can't see them.
I am able to see only one tape drive like IBM ULTRIUM. I should have ADIC drive for jukebox as, and second IBMUltrium drive. The idea is that this driver has to install by itself I guess.
Well yes, Windows install drivers itself provided it is able to detect the devices. For each Autochanger you should have a medium changer and all the devices connected to the server. You can try and rescan for hardware changes to be sure.
If it is not there, check the hardware connectivity. reboot the server and check during boot process on the SCSI card if I think cabling is OK.
I would also recommend installing latest Autochanger & device manufacturer drivers instead of relying on Windows drivers.
"If it is not there, check the hardware connectivity. reboot the server and check during boot process on the SCSI card if I think cabling is OK"
Ok with drivers, but I have checked Connectrix and zone for that, and it seems to be OK. HBAnywhere as well. But what about SCSI card? I have on Device Manager SCSI and RAID controllers and there is EMS Device bus.
Briefly I do not have knowledge to know how to check cabling on SCSI card!
you need to know how is the library connected to your server. if it has worked before you have a device or cabling malfunction. if it is the first time setup most likely you have improper cabling or zoning. use the HBA or SCSI tools to scan the controller for the devices. once you see it there it will be in device manager. until you can see it in device manager you do not need to try to resolve it on networker level.
If your using Fiber drives. You need to assign one of the drives as the controlling drive. Least thats what I did in my Dell Branded ADIC i500 scalar library.
If this tape drive that is the controller is not presented to the server (Management Server or Storage Node), server won't see the library. Only server to see the library would then be the machine that has that tape drive presented to it. (Zoned to that server)
Since you did not mention whether library is SCSI or FC, I assumed it to be SCSI. If it is FC, you do not need to check that. All you need on OS is to make sure you get the library robotics and the tape devices as medium changer & Tape Drives in the Device Manager. Library Robotics is mandatory only if this server is controlling the robotics.
Run the inquire command and check if you get the robotics and drives there. If not clear to you, post the output here.
The same thing is on the Device manager. This is new computer and it is storage node. It works only for one drive (device). I have installed Ultrium Driver.
Microsoft Windows [Version 5.2.3790] (C) Copyright 1985-2003 Microsoft Corp.
C:\Documents and Settings\mb_admin> That one is storage node as well, but I can have two devices (two drives on the jukebox) from this server.The Device Manager gives drive for a changer and two drives for tape. Therefore I can have two devices for each old sever configured as a storage node.
HacknDos1
1 Rookie
•
66 Posts
3881
0
Posted October 1st, 2009 10:00
1) Zoning is setup proper
2) Switch is hard set for 4gb and not on Auto
3) Are the tape drives in use when you are trying to do this? (belive it or not this matters.)
Inquire although useful, will display different information back to a server connected to the same drives, if those drives are in use on a different server. So make sure none of the hardware is in use.
I myself have tried to setup drives on a storage node in the past, and scratched my head as to why doesn't the server see them, and why arent they appearing in inquire, only to come and find out they were in use.
4) Open your HBA software and see if the drives appear there. If they don't, or only one of them does. You need to go back to the switch. OS won't see them if the HBA can't see them.
Paul