UNSOLVED

hbridges

updated

21 years ago

Closed

H

hbridges

16 Posts

0

18704

October 18th, 2005 18:00

installing xp

I have installed a new hard drive in my inspiron 1100.  After hitting enter to start windows setup I get a message that says "Setup did not find any hard disk drivers installed in your computer.  Make sure any hard disk drivers are powered on and properly connected to your computer, and that any disk-related hardware configeration is correct.  This may involve running a manufacturer-supplied diagnostic or setup program."  Any suggestions for what to do next.
  • hbridges

    16 Posts

    365

    0

    Posted October 18th, 2005 18:00

    Sorry I meant to say that setup did not find any hard disk drives.
  • rickmktg

    2 Intern

    •

    11898 Posts

    363

    0

    Posted October 18th, 2005 19:00



    @hbridges wrote:
    Ok, so what is a blade adapter, the dell manual did not mention it.


    Look at your new drive.  See the pins?

    Look at your old drive.  See any pins?  That's the blade adapter.  Remove it, CAREFULLY, and carefully put it over the new drive's pins.

  • hbridges

    16 Posts

    363

    0

    Posted October 18th, 2005 19:00

    Ok, so what is a blade adapter, the dell manual did not mention it.
  • hbridges

    16 Posts

    363

    0

    Posted October 18th, 2005 19:00

    I see what you are talking about but my new drive came with a pin adapter installed so that is not the problem.
  • rickmktg

    2 Intern

    •

    11898 Posts

    365

    0

    Posted October 18th, 2005 19:00



    @hbridges wrote:
    I have installed a new hard drive in my inspiron 1100.  After hitting enter to start windows setup I get a message that says "Setup did not find any hard disk drivers installed in your computer.  Make sure any hard disk drivers are powered on and properly connected to your computer, and that any disk-related hardware configeration is correct.  This may involve running a manufacturer-supplied diagnostic or setup program."  Any suggestions for what to do next.
     
    Using the Advanced Forum Search on the bottom of this page, you can quite easily find the answer to this often asked question.
     
    To add to a recent post, simply click on it, pick Message Options, then Edit.
     
    You probably didn't remove the blade adapter from your old drive and put it over the pins on the new drive.
  • hbridges

    16 Posts

    363

    0

    Posted October 18th, 2005 20:00

    In the bios it list under primary hard drive: 568GB.  I only have a 40GB hard drive. 
    I see no options to do anything with the hard drive (turn in to auto, etc).  Under boot order there is a listing for internal HDD, which i assume is the hard drive. 
  • rickmktg

    2 Intern

    •

    11898 Posts

    363

    0

    Posted October 18th, 2005 20:00



    @hbridges wrote:
    In the bios it list under primary hard drive: 568GB.  I only have a 40GB hard drive. 
    I see no options to do anything with the hard drive (turn in to auto, etc).  Under boot order there is a listing for internal HDD, which i assume is the hard drive. 



    Clearly 568gb is incorrect.

    You need to boot from the CD, so it has to be listed higher on the list than the hard drive.  You may want to look at some of the guides to install Windows XP including the Reinstall Guide located under the Product Support tab, or use the Advanced Search feature at the bottom of the page.  This info is posted several times per day on the forums.

  • rickmktg

    2 Intern

    •

    11898 Posts

    363

    0

    Posted October 18th, 2005 20:00



    @hbridges wrote:
    I see what you are talking about but my new drive came with a pin adapter installed so that is not the problem.


    Then if you're booting to the XP CD (F2 or F12 to boot from CD) and the CD is the drive, it should install XP just fine.

    If not, go into bios and see if the drive is seen.  You may (but shouldn't) need to turn the drive to Auto.

  • hbridges

    16 Posts

    363

    0

    Posted October 18th, 2005 21:00

    thank you for your patience.  I am at the windows xp setup screen that is asking for a partition size.  The maximum is 542253 mb.  This is the number highlighted.  I hit enter to choose this default, like the dell manual suggest but the computer just sits there.  Do I need to choose some other number and if so what?
  • hbridges

    16 Posts

    79

    0

    Posted October 18th, 2005 22:00

    I booted to the cd and get the same message about the partition.  Specifically "542257 MB Disk 0 at Id 0 on bus 0 on atapi (MBR)  Unpartitioned space    542257 MB