UNSOLVED

ferger

updated

22 years ago

Closed

F

ferger

13 Posts

0

16820

February 16th, 2005 07:00

Inspiron 9100 - How can I find my monitor type and where can I get the driver for it?

I have an Inspiron 9100 with the ATI 9800 with 256 RAM and a resolution of 1920*1200 (32-bit) and I can only get 60Hz refresh rate due to the fact that the types of monitors listed in the Display properties are five (5) identical entries named "Default Monitor". I went to the Dell "original system configuration" page and this is what it says about my display:
 
W3866 LIQUID CRYSTAL DISPLAY, Wide Ultra Extended Graphics Array, N-SPWG, 15.4, SAMSUNG, V2
 
Whatever that means...
 
Now, I looked everywhere on the web including Dell's and Samsung's site and I cannot find any drivers for it :(
 
Could someone please help me to resolve this issue and perhaps point me to the right drivers page?
 
Any help is apprecciate it.
 
Thanks in advance!!!
  • Leo_s84

    496 Posts

    390

    0

    Posted February 16th, 2005 12:00

    The LCD doesn't use any driver, so dont bother looking for one
  • 390

    0

    Posted February 17th, 2005 12:00

    Leo84 is right.  You will not find them. The monitor driver is built into the video driver as it's just an LCD screen.  This is WHY you need specific Mobility drivers for your card, and the generic drivers from ATI's site do not work properly without some "additional" patch work being done to them. 

    Your default refresh rate is going to be only 60hz, however due to the characteristics of LCD's vs CRT's you'll see that you don't have the strobing effect that CRT's have at 60hz because the LCD's actually stay lit a few ms longer than a CRT screen does. 

  • ferger

    13 Posts

    390

    0

    Posted February 17th, 2005 15:00

    Thank you both for the info. I was going nuts looking for a driver and now thanks to your answers I wont anymore ;)

    One more question though, to upgrade my ATI 9800 video card should I use the drivers on Dell website and the Catalys driver on ATI site in conjunction ? or should I just stick to Dell's ?

    Please let me know and thanks in advance.
  • Leo_s84

    496 Posts

    390

    0

    Posted February 17th, 2005 20:00

    You cannot use the catalyst in ati's page because it is made for desktop cards.

    Go to www.laptopvideo2go.com and find the latest catalyst modified for laptop usage. They are better than dell's.

  • ferger

    13 Posts

    390

    0

    Posted February 17th, 2005 23:00

    Thanks for the advice Leo. One more question, is the driver that I need from laptopvideo2go one called 806.exe ? Its kind of unclear to me which one to download... sorry.

    Also my monitor after a while it goes black and then I cannot wake it up at all, I move the mouse, pointing stick, touch pad or press the keybord and it does not work... so what I have to do is press the tiny button that depresses when you close the lid and then it wakes up, but I am thinking it shoudl not be like that... any ideas ?? Thanks

  • blaxo

    21 Posts

    390

    0

    Posted February 19th, 2005 16:00

    forget the standard catalyst drivers with .INF hack....

    i would recommend either the DNA or OMEGA drivers for your mobility radeon 9800...

    these drivers are modded versions of the latest stable catalyst builds from ATI - ready to install on ANY ATI video card including ALL mobility chipsets - with many more options to tweak the driver settings (with optimized interchangable openGL drivers for specific games) - and optimized for much higher frame rates in games...


    http://www.dna-drivers.com/ <--------------- DNA drivers

    and

    http://www.omegadrivers.net/ <--------------- OMEGA drivers


    - oh and for your monitor problem - have you gone under power options under the control panel, and checked out the options yet? set the time to standby under "POWER SCHEMES" and then under the "ADVANCED" tab you can change your settings for the buttons to turn on/off standby mode :D


    GOOD LUCK :D
  • ferger

    13 Posts

    390

    0

    Posted February 20th, 2005 03:00

    Thanks for the excellent info about the drivers "blaxo". I wanted to ask you another thing; which one of the two drivers is better? Which would you recommend. Let me know please...
  • blaxo

    21 Posts

    390

    0

    Posted February 20th, 2005 06:00

    see for yourself...

    http://www.onlinegamers.org.uk/forums/showthread.php?t=3150&page=1&pp=15&conly=0

    basically the latest catalyst drivers are build 5.2 (which is better than the 5.1's released at the beginning of feb and benchmarked in this article)... but the modded catalyst DNA and OMEGA drivers are pretty much always faster than ATI's reference drivers due to various tweaks and adjustments to the core driver settings...

    of the MODDED drivers, the DNA's and OMEGA's based on the catalyst 4.12's are supposed to be the fastest (but very soon now there will be new modded releases based on the 5.2's which will likely be faster than both the 4.12's and the 5.1's) .... another article -------> http://www.onlinegamers.org.uk/forums/showthread.php?t=2928

    anyway when it comes down to the differences between DNA and OMEGA, theyre both pretty close, with OMEGA or DNA coming out on top on different tests by only a hair.... i prefer the DNA drivers, as there's an openGL switcher utility which allows you to optimise the driver for many specific games (under programs/DNA in the start menu), but in the end theres not that much difference performance wise between the 2.... (the omega driver based on the 4.12 will get you the highest framerates if you play a lot of halflife2 and farcry though if you take the time to use the openGL switcher, DNA can do just as well if not better)

    :-D