UNSOLVED

thedragonmaster

updated

12 years ago

1

376395

June 8th, 2014 12:00

XPS 8700, CPU fan connector type?

i still have no resolution from my random crashes for 11 months, and off shored support just keeps wanting to replace stuff that's all ready been replaced. so, in my researching i think the system is running hot. I honestly think Dell  the fan curve, if i use "speedfan" to speed up the fans they take 30 seconds to start "stepping up" which could be "to late". So after my waranty goes out next month i want to replace my heat sink. I was considering the ZALMAN CNPS9900MAX-B, but not sure if that will fit. however it dawned on me (i had a DUH moment). Anyone know what the cpu fan connector is? 3pin or 4pin? i tried to look in the manual but i cant tell. I am legally blind and when i zoom in to try and see, all i get is pixelation. i tried searching for the cpu fan on dells part site but apparently they are not listing them, so i cant look there either. i know i could open it up and figure it out. but i want to try and avoid that. so, if any one knows please let me know. thanks :)

  • RoHe

    12 Elder

    •

    45230 Posts

    •

    172625 Points

    7491

    0

    Posted June 8th, 2014 18:00

    Random crashes are hard to fix.

    You don't have to wait until the warranty is out to replace the heat sink. However, if you do replace it, Dell won't provide warranty support for the system with a different heat sink.

    What temps is SpeedFan reporting? Do you get a BSOD, does it freeze, or does it just reboot itself? If you provide some details about the crashes, maybe somebody here can help you find a fix.

    Dell typically uses a fan with a sensor in it. If you replace the fan with a non-Dell fan, you'll probably get an error message every time you boot saying "Fan failure.  Press F1 to continue..." Can you live with that?

    Has the old thermal paste on the heat sink been removed and fresh paste (eg, Arctic Silver) applied?

     Have you updated the video drivers and tested the memory?

     

     

     

  • 7491

    0

    Posted June 8th, 2014 20:00

    ive gone through 11 months of dell support over the same problem, "The computer has rebooted from a bugcheck.  The bugcheck was: 0x00000124 (0x0000000000000000, 0xffffe0000f777028, 0x00000000be000000, 0x000000000100110a)"


    we have done the following driving me nuts in the process.

    1. GPU replacement - self install

    2. reinstall of O/S from recovery partition

    3. reinstall of O/S from flash drive

    4. replace PSU, motherboard, memory modules - they demanded, yes, demanded a tech install.

    5. replace motherboard again, replace hard drive for a "fresh" install of the o/s, replaced memory modules. again a tech install.

    6. reinstall the O/S AGAIN.

    at this point im done with offshore and will never ever buy another dell product again (nor will any one in the family)


    speed fan was reporting incorrect temps, i discovered this after a search for the max temp for the i7-4770 resulted in me downloading and running coretemp and seeing the temps didnt match by a long shot. running at idle (something i should have done from the get go but didnt think about. one of those "im an idiot" moments) showed speedfan reporting 65*f, impossible since ambiant is never below 78*f in this house. i calibrated the offset to match coretemp which was nearer to 80*f. under full load letting the bios control the fan temp is 165*f, i know the fan curve is shot because theres a good 30 second delay before the fans "start" to go up, and then they only "step" up slowly. obviously if a cpu is hitting TJ-MAX those fans should go to max with out "stepping up slowly"


    since i cant reprogram the bios fan curve, and since speedfan cant slow down the fans once its adjusted them up, my solution is to replace the heat sink with all copper and larger fan.

    as for the compound, they replaced that during the last visit, granted i "could" change it out, but the only TIM i have sitting around is some arctic silver ceramique thats about 4 years old, and honestly dont want to pay shipping more than i have to. so would just rather change the case fan, heat sink, and TIM all out at the same time.

    of course if i could convince dell "support" to send me out a replacement that would be nice, but im done with offshore, so unless some one in the U.S. can deal with it, ill just buy the stuff my self.

    all i need to know is, is the fans 3pin or 4pin. the sensor your talking about is the RPM sensor on PWM fans, which most 3/4 pin fans have (i think its a green or yellow wire)

    sorry if i come off grumpy, but after 11 months and being told the same spew over and over again, kinda wears a person down to a point where they just give up. i paid over a grand for this system and it should WORK, i mean it "is" an "extreme performance system" and i shouldnt have to jump through 11 months of hoops to get them to fix it, but ive had it. i just consider it failure to honor the warranty and chalk it up to a "put them on the product ban list" kind of thing

  • RoHe

    12 Elder

    •

    45230 Posts

    •

    172625 Points

    7491

    0

    Posted June 9th, 2014 11:00

    I'd be grumpy too with all those problems.

    Is this Win 7 or...

    Did they ever replace the CPU or have they just been moving the original one from motherboard to motherboard?

    I can't answer your question about the number of pins on fan connector in that model, but I still think a non-Dell fan is going to give an error. That's the way it's been "forever" with Dell PCs, but I don't have hands on experience with this model.

    I'll ping my Dell tech contacts to see what can be done about this while you're still under warranty and before you invest any $ in things that might not help.

  • RoHe

    12 Elder

    •

    45230 Posts

    •

    172625 Points

    7491

    0

    Posted June 10th, 2014 16:00

    My tech contacts say it uses a 4-pin fan connector.

    They advise before you invest in any new heat sink or fan that you remove the existing heat sink, thoroughly clean the old thermal paste off both surfaces. Then apply a thin coat of a good quality paste (eg, Arctic Silver) and reinstall the existing heat sink. Run it that way for a while to see if the suspected overheating problem goes away.

     

     

  • 7485

    0

    Posted June 22nd, 2014 01:00

    thanks, this has been fun. and sadly you cant change out the heatsink (ill explain in a moment)


    for any one searching, yes the cpu fan is a 4pin PWM fan, the rear exhaust is a 3pin 92mm fan.


    the reason you cant replace this heatsink, is because dell in their infinite wisdom do not use the standard lga1150 ILM (independent latching mechanism), if you google search that and look at the back of a motherboard it should be a rectangle, what dell has on here appears to be a combination of that rectangle and the intel stock "x" shaped back plate, so you end up with a X shaped none removeable backplate. with what appears to be threaded rivets through the motherboard heatsink support holes.


    what this means is, any heatsink that uses push pins? wont work, any heatsink that needs its own backplate installed? wont work.

    now, mind you, i gave some thought to changing out the ILM, but, it all so appears this things epoxyd or other wise glued on, and i know my luck.

    in a nut shell? your stuck with the aluminum heatsink.

    i used some arcticlean to clean off the cpu and heatsink, and applied some new artic silver ceramique. ive done that a few times over the years so know i did it right. i use the swipe method (cant stand the "dot" method, it just feels wrong to me) sadly using prime 95 (NOT using small ffts) the cpu hits 180*f and thats with the cpu fan set to 100%

    not exactly what id consider extreme performance, just wish i had realized this sooner. i did consider changing out the motherboard for one with a "correct" lga1150 ILM, but i got a feeling trying to get that 8.1 key transfered would be a night mare, so im just stuck using an "extreme performance system" for, well, basic things.

    hey dell? in the future, consider a copper core heatsink at the least please?

    edit: i forgot to answer you, sorry, its windows 8.1, and they have just been moving the cpu from board to board.

  • RoHe

    12 Elder

    •

    45230 Posts

    •

    172625 Points

    7485

    0

    Posted June 22nd, 2014 17:00

    You didn't say which processor you have or what you were running when the temp hit 180ºF (68ºC). 68ºC doesn't seem all that hot to me. And the CPU will throttle itself down if the temp gets too high, so there isn't too much risk of it cooking itself. Check Intel's site for acceptable operating temps for your specific processor.

    Are you sure SpeedFan is accurate? I used SpeedFan on a Dell Ultrabook with a Gen 4 Core i7, running Win 8.1 and SpeedFan reported temps of >4 MILLION degrees (yes, million) for the CPU, so I have doubts about its accuracy. I reported the issue to SpeedFan's creator but he never responded.

    Have you confirmed your temps with some other monitoring software?

    You may not be able to put a non-Dell motherboard in this case. Dell frequently uses a custom connector between motherboard and front panel, so unless you're prepared to trace the wiring (which Dell doesn't publish)...

    Have you considered installing a PCI card slot fan? Uses an empty slot but doesn't connect to the motherboard circuitry - It only uses the slot for support. It does need a connector from the power supply. Since your power supply probably uses SATA connectors, you may also need an inexpensive SATA>Molex adaptor to connect to a Molex card fan, unless you can find a card fan that uses a SATA power connector.

    Next time it crashes, look in Windows Event Viewer for errors around the time of the crash. That might point you in the right direction, but absence of an error message doesn't tell you anything.

    To me, this is more likely a RAM problem not a heat problem. So let it run for a while so it's warm and then reboot, press F12 and run the RAM tests from the Utilities partition on the hard drive. Or make a bootable CD with memtest86+ (free) on it and see what happens.

  • 7485

    0

    Posted June 23rd, 2014 00:00

    You didn't say which processor you have or what you were running when the temp hit 180ºF (68ºC). 68ºC doesn't seem all that hot to me. And the CPU will throttle itself down if the temp gets too high, so there isn't too much risk of it cooking itself. Check Intel's site for acceptable operating temps for your specific processor.

    yes i did, post from 8 june 2014 8:27 PM i pointed out that its an intel i7-4770, intel states the jtmax is 212*f so 180*f coming with in 32*f of "melt down" to me is not acceptable, and having a system consistently do that for 11 months your telling me it would cause no harm? nuh uh, sorry, it would.

    Are you sure SpeedFan is accurate? I used SpeedFan on a Dell Ultrabook with a Gen 4 Core i7, running Win 8.1 and SpeedFan reported temps of >4 MILLION degrees (yes, million) for the CPU, so I have doubts about its accuracy. I reported the issue to SpeedFan's creator but he never responded.

    Have you confirmed your temps with some other monitoring software?

    again, exact same post i pointed out i used "coretemp" to check

    Have you considered installing a PCI card slot fan? Uses an empty slot but doesn't connect to the motherboard circuitry - It only uses the slot for support. It does need a connector from the power supply. Since your power supply probably uses SATA connectors, you may also need an inexpensive SATA>Molex adaptor to connect to a Molex card fan, unless you can find a card fan that uses a SATA power connector

    thats a nice idea, if the slots where above the cpu, the issue is the cpu. if a delta fan pulling 90CFM literally inches from the cpu isnt goint to cut it, then i doubt a slot fan will.

    Next time it crashes, look in Windows Event Viewer for errors around the time of the crash. That might point you in the right direction, but absence of an error message doesn't tell you anything.

    again, answered and answered in previous posts, there is "nothing" before the crash other than heat spikes

    To me, this is more likely a RAM problem not a heat problem. So let it run for a while so it's warm and then reboot, press F12 and run the RAM tests from the Utilities partition on the hard drive. Or make a bootable CD with memtest86+ (free) on it and see what happens.

    you are kidding right? again, previous posts, the memory has been replaced completely TWICE, and ive ran dells tests hundreds of times over the last 11 months, no, not an exageration. it is NOT THE RAM

    i know, i know, impossible to believe its the cpu, impossible to believe a user actually, you know, tests things. but this exact same mentality is why ill never buy a dell again, they dont listen. would you prefer i scan all the orders where they replaced the memory? and other parts? must i actually video every single memory test to prove its not the memory?

    as for what program i used, i pointed that out to. running einstein (a boinc project), or prime95, yes 180*f is to darn high. especially when thats not the max it goes. did you think that maybe its spiking to tjmax (which is not a throttle limit, thats "holy <ADMIN NOTE: Profanity removed as per TOU>you melted the solder holding the heat spreader on to the core" temperature)

    why the heck is it so hard for dell and its fans to believe that dell released something with a design defect?

  • DELL-John C

    7 Practitioner

    •

    353 Posts

    7485

    0

    Posted June 23rd, 2014 08:00

    Hi thedragonmaster,

    I've sent you a friend request with my e-mail address so that you can contact me personally regarding this issue. If you can get in touch through this, I'll be more than happy to address the issues that you're experiencing with your system and with Dell support.

    Thanks in advance and I hope to hear from you soon.

  • ulieq

    1 Rookie

    •

    35 Posts

    7485

    0

    Posted January 27th, 2015 14:00

    I'm going to be replacing the case fan in my xps 8700 with a quality ARCTIC F9 TC case cooler.  My only concern is this: Will I get a prompt saying CASE FAN FAIL each bootup just because I'm not using the Generic, Loud low quality Sunon Brand lawn mower in my machine, or will it work like it's supposed to?  

  • Dan-H

    6 Operator

    •

    1217 Posts

    1334

    0

    Posted January 27th, 2015 23:00

    I'm going to be replacing the case fan in my xps 8700

    It might be better if you started a new discussion around case fans instead of jumping into a CPU cooler discussion.

    Just sayin...