UNSOLVED

cademetz

updated

19 years ago

C

cademetz

2 Intern

•

1327 Posts

0

49240

August 17th, 2007 15:00

XPS 720 - nTune - Fan Control Issues

I may be missing something very fundamental, but I can't seem to truly control the fans via nTune. I've observed the following:
 
- Once switching from automatic to direct fan control, the fan speeds speed up slightly even though the sliders are left untouched.
- The CPU fan cannot be set to maximum in one step. If I set it to 100%, it speeds up only slightly. I set it to 100% again, it speeds up slightly again. I have to repeat this process until it finally reaches 100%.
- The CPU fan cannot be reduced in speed once it has been manually increased. It takes a system reboot to reset the fan.
- The system fan can be set to maximum in one step, but cannot be reduced in speed in one step. It has to be reduced in speed step by step (similar to increasing the CPU fan).
 
So, any experience from XPS 7x0 owners controlling your fans?
  • cademetz

    2 Intern

    •

    1327 Posts

    706

    0

    Posted August 17th, 2007 16:00

    Shameful self posting to bump it to the top...  seems all the moving around is wreaking havoc with thread sorting.
  • tphillips63

    4 Apprentice

    •

    2629 Posts

    •

    7922 Points

    706

    0

    Posted August 17th, 2007 19:00

    Yeah I hoped it would be better. It never was very good on the 700/710 either. I think it is a three steps forward one backward program. It has gotten much better over the past year but its still not right yet. On my 710, when I try to manually control the fans it puts them at 80% and then climbs to full speed. lol it's so loud it drives me mad. All I can do is turn it off to reset it. This has happened on each version I try.
  • tphillips63

    4 Apprentice

    •

    2629 Posts

    •

    7922 Points

    706

    0

    Posted August 17th, 2007 19:00

    cadmetz, Did you enable in the BIOS all the advanced memory timing for SLI/EPP and overclocking? I know on the older boards they both need to be enabled for ntune to control the board settings.
  • cademetz

    2 Intern

    •

    1327 Posts

    706

    0

    Posted August 17th, 2007 19:00

    I have enabled "Performance Application Settings" which is what allows nTune to control the various settings on the motherboard (nTune wouldn't even install until I enabled this). Also, since I have the Corsair memory, the EPP memory setting is enabled as well.
     
    nTune can control things... to a point, but I would it's not the kind of control I was expecting.
  • cademetz

    2 Intern

    •

    1327 Posts

    706

    0

    Posted August 17th, 2007 20:00

    Well, I guess it's good to know I am not the only one with the issues. -- Thanks
  • BubBowen

    635 Posts

    706

    0

    Posted September 7th, 2007 15:00

    Same thing happens to me.
     
    I want to increase my fans a litle while Folding, but then it all goes to heck in hand basket real quick.
     
    Bub
  • buckZor

    1 Rookie

    •

    58 Posts

    706

    0

    Posted February 3rd, 2008 17:00

    I wanted to add to this thread that it would appear nTune is incorrectly accessing fan control on our 720 motherboards.  Simply installing nTune and enabling the performance control in the bios will increase your system fan speed by 6%.  This is audibly noticeable.  Every time nTune accesses your system mainboard you will incur a 6-7% fan speed increase.  This is very noticeable as you make voltage modifications or any time you force nTune to access the mainboard by clicking apply. 

     

    It's worse with the version 6 beta for Windows 64-bit.  I am unable to REDUCE fan speed at all, everytime I try I incur another 6-7% speed increase in system fans.  Because of this I am unable to make ANY changes with nTune because even by applying a profile I incur a 6-7% fan speed bump, and I want my system QUIET.

     

    If anyone has any suggestions please post or PM.  The nVidia forums don't even have an nTune section :(

  • garyehr

    50 Posts

    706

    0

    Posted February 3rd, 2008 17:00

    Are you using N-Tune 5.05.54 or are you usining Nvidia's new program "nforce system tools". There new program works very well for me and i have no problem contolling fan speeds on both of my ultra cards. This is the program that Nvidia is going to replace ntune with. You can get it on their site.

     

     

     

    XPS720H2C
    Windows Vista Ultimate 64
    Norton Security 2007
    Microsoft Office 2007
    Intel® QX6700 @ 3.53Ghz
    4Gb OCZ Reaper DDR2 PC2-8500DDR2-1066
    320g 10K hard drive
    Dual nVidia GeForce 8800 Ultra 786Mb Memory
    Creative Sound Blaster X-Fi Xtreme Sound Card
    BlueRay Drive
    Broadcom 5754 Ethernet NIC NetXtreme
    Dell 24" LCD Monitor
    Logitec Cordless MX 5000 Desktop Keyboard & Mouse
    19 in 1 media card reader and Floppy drive

  • buckZor

    1 Rookie

    •

    58 Posts

    706

    0

    Posted February 3rd, 2008 18:00

    To be specific, I am talking about the "nForce System Tools with ESA Support", version 6.00 at this download link: http://www.nvidia.com/object/nforce_system_tools_6.00.html

     

    I am not trying to control my GPU fans, but my Dell system fans.. well actually, I don't want to control those fans either, I am trying to make RAM voltage modifications but everytime I do that nTune bumps my system fans up by 6-7%. 

     

    Actually, I am noticing now that this is no longer beta, perhaps this is a newer version and I will try it now.

  • buckZor

    1 Rookie

    •

    58 Posts

    546

    0

    Posted February 3rd, 2008 19:00

    Yay! this new version release has corrected my problem!  It does initially bump your system fan speeds up by the 6-7% but you can lower it back down, apply and it sticks!  Woot, time to tweak my RAM :)