
UNSOLVED
VGA on XPS 8500 stopped working
My XPS 8500 is only a few weeks old, from day 1 I enabled the on board VGA so I could run two monitors, the other off the supplied graphics card.
One day PC failed to power up and a new Mobo installed, all working fine.
Bought a new 27" monitor to replace the two 17", all working fine.
Decided that another screen would still be handy so reconnected a 17" - no display on the 17", power light stays amber so no signal getting through.
Called support, could not fix the problem so thought another faulty mobo, had this replaced by Dell engineer and the onbaord VGA still doesn't work.
The 17" and cable has been tested on another PC and they work fine.
Multi-monitor support in BIOS has been enabled.
Windows does not detect 17" monitor via VGA, does detect if I plug into the DVI of the graphic card.
Any idea's why the VGA has decided not to work?
Cheers
Dave
Responses (9)
Solutions (0)
Dell-Zohaib R
4 Apprentice
•
953 Posts
1145
0
Posted July 26th, 2012 15:00
Hi hithero,
I apologize for the delay in responding.
In case, you want to use multiple monitors only with your Onboard Video Card(i.e., Only Onboard VGA Port and Onboard HDMI Port), you need to enable the Intel Multi-Diplay option in the BIOS by following the below steps:
1. Start tapping the F2 Key when Dell Logo is seen during startup.
2. After entering the System Setup Navigate to the Advanced tab using the Right Arrow Key on the keyboard.
3. Then navigate to the Onboard Device Configuration.
4. After that go to Intel Multi-Display and Enable it.
Next step is to download and install the latest drivers for the Onboard Intel Graphics from any of the following Links:
However, please be informed that as per the information shared by Intel Corporation on their website - “Intel graphics cannot be used along with an external PCI Express graphics controller. Installing a PCI Express graphics controller will disable Intel graphics.” You can check the following link for more details:
www.intel.com/.../cs-031040.htm
Since, I have found this information I have shared it with you. Still if there are any other solutions that other users on the forum had tried, while attempting to fix the same problem, you may try the same at your discretion.
Hi Zohaib. Thanks for finding this info but that just confuses matters even more as from day 1 I had been running monitors of the intel VGA and the DVI from the Dell install PCI express graphic card and it has stopped working. I've been in touch with Dell support and they spent 2 hours trying to get the combination to work again, I have a Dell engineer comming today to replace the motherboard and graphics card, hopefully this will set it right again.
Cheers
Dave
The Dell engineer has replaced the motherboard and graphics card and told me that the card will alway's disable the onboard graphics, and left with the set-up not working.
I managed to get the set-up working.
The monitors were both plugged into the graphics card (DVI & HDMI) and working.
I removed the HDMI lead completely and replaced with the VGA to the motherboard and re-booted.
Immediately upon start-up the system noticed the change and re-started itself and did this once more.
It booted initially on the VGA screen, once windows had loaded Catalyst recognized the DVI as screen 1 and the primary monitor. All seems to be working again, maybe the BIOS will only accept both graphics to work if the set up is made in a strict order?
Cheers
Dave
Dell-Zohaib R
4 Apprentice
•
953 Posts
1145
0
Posted July 27th, 2012 12:00
Hi hithero,
Thank you for keeping us updated. In case, there is any other problem in future feel free to get back to me.
pinoyrukus
5 Posts
1145
0
Posted December 21st, 2012 18:00
Have you tried using the hdmi/dvi off the graphics card and the hdmi off the mobo? I'm trying to find out if I can do a triple monitor setup this way. Thanks
I have a XPS 8500 i7 3770 & went through the same problem. The Tech. guy called me just now to come and replace the motherboard, because I couldn't get into BIOS. Luckily the BIOS problem was all based on the keyboard I have (Logitech G510), and the tower doesn't have a ps/2 port for the older keyboard I have. So, I went to OfficeDepot and got a ps/2-usb adapter, plugged in the old keyboard, and got into BIOS, enabled the dual monitoring. Still didn't work though. After research I went ahead and unplugged my DVI (main monitor), and plugged in the VGA (2nd monitor) and booted up. The old monitor was working, so while the OS was running, I plugged in the DVI monitor, and whaBAM!, I had two monitors on. Then, all I had to do was go into display properties and switch the monitors so that I had 1 & 2 in the correct order. Any questions, please ask, as going through so much trouble I would enjoy helping someone out. That, and I think I could be more supportive than Dell themselves. :emotion-15:

Dell-Zohaib R
4 Apprentice
•
953 Posts
1145
0
Posted July 19th, 2012 12:00
Hi hithero,
Welcome to the Community.
Thank you for the detailed information about the problem. From you post it is clearly evident that you have tried multiple monitors at the same time by connecting them to both onboard VGA Port as well as the Port(s) on the Graphics Card. However, I am curious to know if you have removed Graphics card from the system and tried connecting the 17” monitor to the onboard VGA Port?
I would request you to try the above mentioned step and reply back to me.