
UNSOLVED
Precision T7400 workstation sounds like Concorde taking off
Hi,
I've taken delivery of a Precision T7400 workstation with the following spec:
Dual Intel Xeon X5482 (3.20GHz,1600FSB,2x6MB,Quad Core)
Vista 64Bit
8GB 800MHz ECC Memory
512MB PCIe x16 nVidia Quadro FX 1700 (MRGA14L), Dual Monitor DVI or VGA Graphics Card
I haven't had a chance to call Dell Support yet or ensure that I've got all the latest drivers and Vista updates but this thing sounds like Concorde taking off when it's sitting doing nothing! I'm talking about it being so loud I can't really sit and work on it at the moment.
I'm still in the process of getting network access in the office so I don't have the internet as of yet.
Just wondering if anyone else has experienced the same problems and solved them by updating the OS or drivers so I don't need to worry about it too much. I think I've probably got one of the first of these in the UK with the 3.2GHz CPUs because there was a problem with them which they've only just solved. I thought I'd try here on the off chance anyway.
Cheers,
Jim
Message Edited by oopsltd on 02-03-2008 02:43 PM
Responses (44)
Solutions (0)
Hi CueBoy,
Thanks for your suggestions. I'll check it out tonight and see what I can see.
There were no error messages as far as I remember. It seemed to me that the fans got louder the longer the machine was switched on until they were a real din. Perhaps there's a problem with the door or the plunger in that case? Fingers crossed but I do have onsite maintenance although it's a pain if I have to call them out.
Cheers,
Jim
Message Edited by oopsltd on 02-04-2008 11:25 AMHi CueBoy,
I've been having trouble logging in here all night but I finally made it!
I checked the plunger-switch and it seems to be connected up ok. I made sure that the case was closed properly too but it still sounds like the fans are on full speed for no reason. I've not had a look at the CPU heatsinks or anything yet but if they're at fault then it's an outcall for Dell support anyway.
I'll hopefully get the machine online by the end of the week, install all the latest patches, etc. and then if it still sounds like it wants to take off I'll call support.
Thanks for your help in any case.
Cheers,
Jim
Maybe you can run Everest or something similar and get the RPMs of the various fans.
I got a Prec 690 without risers - that was dead quiet. Then I got another one with risers .. the memory fan was > 2400rpm at idle. That was too loud. I had to return it. The presence of memory risers result in a different case and the fan is somewhat louder. However my unit was probably had a problem also.
I have no idea about the T7400 so cannot be more helpful. But identifying the rpms may help.
Hi krishd,
I think you're right about the memory fan and risers being the culprit. I read a review today of the Intel Skulltrail platform and it mentioned that the FD-DIMM RAM gets very hot and needs its own fan. They suggested adding a fan speed controller to tone it down a bit. When I talk to Dell support I'll ask them about this because the machine is just too loud for an office as it is. I'd need earplugs.
Cheers,
Jim
hi oopsltd,
I am currently installing my own t7400 and wondering if you can do me a favour and answering me one question.
Is there an air temperature sensor connector on your t7400's system board?
I have just got my system board today and I cannot figure out where to plug in the temperature sensor from the i/o panel.
thanks a lot in advance for your help!
James
Hi James,
I see. Well, I'm wondering myself if there are temperature sensors in the thing at all as well.
I did a 100% CPU load test using some software I downloaded and the machine was actually quieter during that than it was at idle earlier on today after I'd started an IE session. Something definitely isn't right in any case. I hope the guy coming tomorrow knows his stuff and can get to the bottom of it.
Cheers
Jim
Hi Jim,
Well, I am building my t7400 from barebone and that's why I am in trouble now.
The temperature sensor cable from i/o panel has nowhere to plug into on the system board.
Am wondering if the system board I got from dell is faulty, or maybe the i/o panel is wrong. :(
Thanks for your reply!
Cheers
James
what you describe is very strange Jim. it does sound like the temperature sensor is not working properly.
if you look inside your machine the temp sensor is connectted from the i/o panel via the thin twisted pair black and red cable and go under the cage card fan and connect to the motherboard's 2 pin connector just in front of the fan.
I can certainly see the print (FR_THRM) and a pin hole on the motherboard but the 2 pins connector is missing on my motherboard.
if you look at the manual
<ADMIN NOTE: Broken link has been removed from this post by Dell>
it says the temp sensor must be connected at all time while the machine is on or may result in thermal problem- such as fans running at full speed etc..
maybe you should look if it is connected correctly.
cheers
James

CueBoy
37 Posts
2936
0
Posted February 4th, 2008 00:00
When the fans start, do they turn all the way on immediately when you turn on the unit, or do they take a while to get there?
If they're taking a while, then check to make sure the side door is properly closed. The system is programmed to speed up the fans (and complain to you) if it thinks the door is missing. If the door is properly installed, check for the presence of a small black plunger-switch - this is what the door presses against to tell the unit it is present. Does that switch seem to work normally? Is it plugged into the motherboard?
If everything related to the door appears to be correct, check over the heat sink (or sinks?) that cover the CPU(s). If those aren't installed properly (check to see if they move around at all). If the CPUs are overheating for some reason the fans will speed up.