UNSOLVED

cs2870

updated

11 years ago

C

cs2870

1 Rookie

•

17 Posts

0

219581

February 26th, 2014 19:00

New install win7 on Inspiron 530 can't enable ahci mode despite best efforts

Can't seem to enable ahci mode on inspiron 530 quad core despite futile , exhausting efforts trying everything I can find on this site and others. 

I did a new install of win 7 64 bit , and I made sure I enabled "raid" mode in the bios before installing. Note there is no "ahci" mode in this bios, only options are "ide" and "raid". Raid is supposed to allow ahci mode, yet no luck so far. I can boot into windows just fine, it's just not recognizing that ahci isavailable. Here are some screenshots 

I have tried many different driver versions, different versions of Intel matrix storage manager / intel rst, I tried a regedit file from dell, nothing seems to help. 

  • cs2870

    1 Rookie

    •

    17 Posts

    2062

    0

    Posted February 27th, 2014 09:00

    Really hoping to find some help with this. Thanks!

  • rdunnill

    8 Professor

    •

    8811 Posts

    •

    35254 Points

    2062

    0

    Posted February 27th, 2014 12:00

    Trying this with a Vostro 220s, which AFAIK has a similar motherboard.

  • rdunnill

    8 Professor

    •

    8811 Posts

    •

    35254 Points

    2062

    0

    Posted February 27th, 2014 15:00

    Have you updated the BIOS to the latest version?

  • cs2870

    1 Rookie

    •

    17 Posts

    2062

    0

    Posted February 28th, 2014 09:00

    yes I updated the bios a long time ago and verified it was still the latest version when I started this troubleshooting process

  • speedstep

    11 Legend

    •

    46969 Posts

    2062

    0

    Posted February 28th, 2014 10:00

    It will not install without AHCI Sata mode enable in BIOS.

    I would suggest

    http://www.apricorn.com/products/desktop-ssd-hdd-upgrade-kits/vel-solox1.html

     

    Newer Versions of the INTEL RST drop support for older chipsets aka

    Intel® 82801HR/HH/HO I/O Controller Hub (ICH8R/DH/DO)

     

    AHCI is built into chipsets with the following controller hubs:

    • Intel® PCHM RAID/AHCI controller hub
    • Intel® PCH RAID/AHCI controller hub
    • Intel® ICH10R/DO SATA RAID/AHCI controller hub
    • Intel® ICH10D SATA AHCI controller hub
    • Intel® ICH9M-E SATA RAID/AHCI controller hub
    • Intel® ICH9M AHCI controller hub
    • Intel® 82801IR/IO Controller Hub (ICH9R/DO) - RAID and AHCI
    • Intel® 82801HEM I/O Controller Hub (ICH8M-E) - RAID and AHCI
    • Intel® 82801HBM I/O Controller Hub (ICH8M) - AHCI only
    • Intel® 82801HR/HH/HO I/O Controller Hub (ICH8R/DH/DO) - RAID and AHCI
    • Intel® 631xESB/632xESB I/O Controller Hub - RAID and AHCI
    • Intel® 82801GHM I/O Controller Hub (ICH7MDH) - RAID only
    • Intel® 82801GBM I/O Controller Hub (ICH7M) - AHCI only
    • Intel® 82801GR/GH I/O Controller Hub (ICH7R/DH) - RAID and AHCI
    • Intel® 82801FR I/O Controller Hub (ICH6R) - RAID and AHCI
    • Intel® 82801FBM I/O Controller Hub (ICH6M) - AHCI only

     

    I would start with (AHCI) driver version 9.6.0.1014 for Intel® Desktop Boards and work backwards.

    https://downloadcenter.intel.com/detail_desc.aspx?agr=N&ProductID=&DwnldID=15251

    Intel® Rapid Storage Technology Driver 9.6.0.1014
    PCI\VEN_8086&DEV_2681&CC_0106.DeviceDesc    = "Intel(R) ESB2 SATA AHCI Controller"
    PCI\VEN_8086&DEV_27C1&CC_0106.DeviceDesc    = "Intel(R) ICH7R/DH SATA AHCI Controller"
    PCI\VEN_8086&DEV_27C5&CC_0106.DeviceDesc    = "Intel(R) ICH7M/MDH SATA AHCI Controller"
    PCI\VEN_8086&DEV_2821&CC_0106.DeviceDesc    = "Intel(R) ICH8R/DH/DO SATA AHCI Controller"
    PCI\VEN_8086&DEV_2829&CC_0106.DeviceDesc    = "Intel(R) ICH8M-E/M SATA AHCI Controller"
    PCI\VEN_8086&DEV_2922&CC_0106.DeviceDesc    = "Intel(R) ICH9R/DO/DH SATA AHCI Controller"
    PCI\VEN_8086&DEV_2929&CC_0106.DeviceDesc    = "Intel(R) ICH9M-E/M SATA AHCI Controller"
    PCI\VEN_8086&DEV_3A02&CC_0106.DeviceDesc    = "Intel(R) ICH10D/DO SATA AHCI Controller"
    PCI\VEN_8086&DEV_3A22&CC_0106.DeviceDesc    = "Intel(R) ICH10R SATA AHCI Controller"
    PCI\VEN_8086&DEV_3B29&CC_0106.DeviceDesc    = "Intel(R) 5 Series 4 Port SATA AHCI Controller"
    PCI\VEN_8086&DEV_3B2F&CC_0106.DeviceDesc    = "Intel(R) 5 Series 6 Port SATA AHCI Controller"
    PCI\VEN_8086&DEV_3B22&CC_0106.DeviceDesc    = "Intel(R) 5 Series/3400 Series SATA AHCI Controller"

     

     *************************************************************************

    In version 8 I see Raid ATA and I  DO NOT see AHCI

    DiskName                                    = "Intel Rapid Storage Technology Driver"
    *PNP0600.DeviceDesc                         = "Intel RAID Controller"
    PCI\VEN_8086&DEV_2682&CC_0104.DeviceDesc    = "Intel(R) ESB2 SATA RAID Controller"
    PCI\VEN_8086&DEV_27C3&CC_0104.DeviceDesc    = "Intel(R) ICH7R/DH SATA RAID Controller"
    PCI\VEN_8086&DEV_27C6&CC_0104.DeviceDesc    = "Intel(R) ICH7MDH SATA RAID Controller"
    PCI\VEN_8086&DEV_2822&CC_0104.DeviceDesc    = "Intel(R) ICH8R/ICH9R/ICH10R/DO/5 Series/3400 Series SATA RAID Controller"
    PCI\VEN_8086&DEV_282A&CC_0104.DeviceDesc    = "Intel(R) ICH8M-E/ICH9M-E/5 Series SATA RAID Controller"

  • rdunnill

    8 Professor

    •

    8811 Posts

    •

    35254 Points

    2062

    0

    Posted February 28th, 2014 10:00

    I clean-installed Windows 7 Professional x64 on the 220s, updated the chipset drivers with the latest versions from Intel, and then installed the Intel SATA AHCI driver. (It is version 11.6.0.1030, dated 09/01/2012.)
  • CraigAT

    6 Posts

    2062

    0

    Posted March 2nd, 2014 08:00

    Any luck with this?

    I've just bought the 250GB 840 Evo too for my Quad core Inspiron 530. Whilst I've been considering upgrading the PC I was hoping the performance boost would make it last a little longer.

    I too intend to do a fresh install of either Windows 7 x64 or 8.1.  I've updated to the latest bios 1.0.18 and understand I should pick RAID in the bios.

    I just want everything to work the best it can. I believe the performance will still be limited by the SATA ports but should be a noticeable improvement over a standard Hdd.

    Please let us know if you get it working.

    I'll have a go myself once mine arrives.

    Craig

  • cs2870

    1 Rookie

    •

    17 Posts

    2062

    0

    Posted March 3rd, 2014 22:00

    I have arrived at a solution. I will post pictures and step by step as soon as I can, I have been extremely busy and have not had a chance to compile my screen shots. I spent a considerable amount of time researching this, but the solution is pretty easy. It requires flashing a new bios, but not the one from Dell, to enable the AHCI mode, and then it will need a driver update to arrive at full potential. 

     It's quite ridiculous that they never released an updated bios with AHCI, when the dell  BIOS is capable of RAID. Generally, if you can do SATA RAID, AHCI is assumed as a given. You should not have to buy additional hardware to get functionality that already exists on the motherboard. 

  • CraigAT

    6 Posts

    2062

    0

    Posted March 4th, 2014 03:00

    I'm going a slightly different route.  I've purchased the StarTech PEXSAT32.  I got it for less than £25 from Amazon.

    My plan is to install the card and run the SSD from it's SATA3 interface. I've seen a few reports that the SATA interface and the card will be limited by the PCI Express port to either 250 or 500 MB/s per lane (slower than my SSD) :emotion-9:.  The manual doesn't state whether the second slot is PCI Express v1 or v2.  But hopefully the speed improvement will still be worthwhile.

    Also by not having to change the BIOS setting to RAID, I can still run my other 2 hard drives normally.

    I haven't actually tried plugging in my SSD and two other hard drives (plus a DVD drive) to the SATA on the motherboard and enabling RAID but there seems to be issues with this from what I've read.  Would it expect me to set up a RAID array?  Can the drives function independently (under RAID mode)?

    Working in IT, I'm going to look out for an old PC, a mini tower (for the 3 drives) with a socket LGA 775 motherboard (for my Q6600) that will take 8GB of RAM, can do AHCI and possibly a SATA3 port (so looking for a board circa 2009).  If I can find one then it may be goodbye to the trusty Dell.  Though it will only be a stop gap to a new i7 PC when finances allow.

    Interested to see how you get on...

    Craig

  • CraigAT

    6 Posts

    1319

    0

    Posted March 4th, 2014 06:00

    I think you're right that the SATA2 speed may be better than the SATA3 via PCI Express, especially as it is processed on the motherboard too.

    I'm not interested in my current Win7 installation (and hence editing the registry), I intend starting fresh on the SSD.

    I am a little worried about flashing the BIOS - not so much the process but when I've flashed the ROM on my phone I'm always suspecting the ROM when something goes bad.

    My main worry is even after flashing the BIOS will I be able to connect up and have working all of the following:

    Sata1 - 256GB SSD
    Sata2 - 1TB HDD
    Sata3 - 250GB HDD
    Sata4 - DVD Drive

    Also where is the BIOS to be flashed coming from??

    Am I correct in saying I suspect they won't work if I just enable RAID in the BIOS now?


    I am still considering sending the SSD and the card back and waiting until I get a new PC. :emotion-42:  I bought the drive because it had a good write up and was a good price.


    Craig