UNSOLVED

khaught

updated

18 years ago

K

khaught

1 Rookie

•

81 Posts

0

12115

September 14th, 2008 18:00

Lighting FX Lower Panel not working on 720 H2C

Good day. I have a XPS 720 H2C & last night I turned my computer on and the Lighting FX is not working in the lower half of my computer for some reason. I rebooted and pressed F2 and checked it in setup and everything was fine. I tried the Dell Quickset and again everything looked okay. How can I turn the bottom half lighting back on?

 

Excerpt from DELL Chat. Anyone else experience this problem? DELL technician said that it is most likely burnt out. Hmm, I have only had this computer (new) since the end of June. Your thoughts? Thanks.

  • Davet50

    6 Operator

    •

    14442 Posts

    458

    0

    Posted September 14th, 2008 20:00

    If you open the side panel and look at the front I/O board where the power button is located you will see the connection labled upper and lower leds. Make sure they are connect tight. If so you and swap them and see if the conditions change.
  • MoneyGuyBK

    2 Intern

    •

    2294 Posts

    458

    0

    Posted September 14th, 2008 20:00

    If it's under warranty, have Dell send Tech Support.

     

     

     

     

    Peace

     

     

  • khaught

    1 Rookie

    •

    81 Posts

    458

    0

    Posted September 15th, 2008 01:00

    Yep, already checked that Dave. Thanks Money as well, DELL is sending a local technician the part and I expect a call within a day or so. Just thought by chance that there was something I missed or inadvertently disabled. Appears not, and will be covered under warranty. Thanks again for your insight. :manhappy:
  • Davet50

    6 Operator

    •

    14442 Posts

    458

    0

    Posted September 15th, 2008 12:00

    Please let us know what the outcome was. That info might be useful in the future.
  • MoneyGuyBK

    2 Intern

    •

    2294 Posts

    458

    0

    Posted September 16th, 2008 17:00

    Hopefully you will be back in biz before week's end!

     

     

     

     

    Peace

     

     

  • Davet50

    6 Operator

    •

    14442 Posts

    458

    0

    Posted September 16th, 2008 17:00

    Not to make an issue but the cable is bad. if you swap and it follows the cable then the cable is bad unless you swapped at the motherboard end. however with a new board I will still say its just the cable. But hey if they want to swap the board so be it.
  • khaught

    1 Rookie

    •

    81 Posts

    458

    0

    Posted September 16th, 2008 17:00

    DELL Tech here and gone. Replaced front I/O panel and didn't make any difference. Swapped cables from top to bottom LEDs and guess what, the bottom worked but the top did not. So, they are ordering the cable which connects the front I/O to the motherboard and another motherboard replacement. The tech and I had a good conversation and both of us suspect the motherboard since cables rarely go bad. So both have been ordered and most likely will be replaced tomorrow or the next day. I will report back once this has been completed. BTW, the tech removed the front lighting "sticker" between top and bottom front panel when replacing the front I/O. Yes, I said sticker! I didn't know that it was a sticker where all of the diagnostic number and front USB & Firewire display is. DELL did not send that with the front I/O replacement part. If you should ever need to replace the front I/O, request the sticker for that as well. Luckily mine was still sticky enough and adhered well when tech replaced it. He said it needed to be removed in order to seat the front I/O panel correctly. :mansurprised:

  • MoneyGuyBK

    2 Intern

    •

    2294 Posts

    458

    0

    Posted September 16th, 2008 23:00

    On Site Techs get paid on a per job basis.

    And it's not very much.....


    Considering their expenses, and in some cases the gas and distance, of course they would much rather get paid for two jobs (or more) per trip ;)

     

     

     

     

     

     

    Peace

     

     

  • khaught

    1 Rookie

    •

    81 Posts

    458

    0

    Posted September 16th, 2008 23:00

    Dave, that was my first thought also. However the tech convinced me that it was worth it to swap the board out as well. My response, "Okay, as long as it works properly and doesn't create another issue." This will be the third motherboard for my system since I received it in late June. :mansurprised:

  • khaught

    1 Rookie

    •

    81 Posts

    135

    0

    Posted September 18th, 2008 05:00

    UPDATE... Technician arrived today and I passed on our thread discussions. We decided to try the cable replacement first withour rerouting. Fired up the Beast and all front panel lights lit up (kudoos to Davet50--nice call bud!). However, we noticed that the second MB replacement had a different part number than the third replacement board they sent this time. My original configuration was a U723D but DELL's second replacement board was a OP611C. After researching and chatting with DELL rep., found out that yes indeed the third MB (U723D) was the correct part and needed to replace it from the second MB (OP611C). This was based primarily due to my processor (QX6850). While replacing the board, we discovered the original problem with the front panel lights. The I/O cable apparently had been cut during original build and the cable just gave up the ghost the other night. So short of the long story... everything is now original specs and is working great (knock, knock, knock... on wood!). I appreciate the expertise advice I receive from DELL forum members. You guys rock (Davet50 & Money)! This type of input also assists techs when they arrive to do parts replacements. It is refreshing to be able to have accurate, intelligent conversations here and overall assists consumers and techs alike. Keep up the great work guys and I will continue to assist in this endeavor as well. For now, problem RESOLVED!!! :manvery-happy:
    Message Edited by khaught on 09-18-2008 01:25 AM