UNSOLVED

stillwater murp

updated

20 years ago

0

8188

July 22nd, 2006 17:00

Hard drives not seen...Dimension 4600

Help me Obi Wan, you're my only hope...
 
History: about 3 weeks ago, after no modifications or other 'tinkering' with a then-running system, I began getting a 'Primary Drive 1... and 0... not found' error during boot.  I've chatted with Dell mulitiple times.  The first time, they had me simply unplug everything but the bare minimum and it booted fine.  The problem returned, however, and the next time (after solution 1 no longer worked), they had me do the ALT+E stuff within setup and that also worked (for a day).  Most recently, they suggested that the motherboard must be bad, so I installed a new, but with the same problem.  I've tried new hard drive cables also, but to no avail.  Reading the forums makes me want to try flasing the BIOS, but would like to ask anyone here for other possible solutions (and without a floppy drive, how do you flash the BIOS).

Thanks in advance oh wise ones...
Kiley
 
  • Majestic

    2 Intern

    •

    9371 Posts

    132

    0

    Posted July 22nd, 2006 20:00

    As for the ALT + E, make sure the Dell Tech had you do the proper NVRAM clearing for your model.  The procedure I have listed below is the correct method for the 4600.
    • Reboot system and enter the BIOS Setup by pressing F2.
    • Turn on Caps Lock, Scroll Lock and  Num Lock.
    • Press ALT + E then ALT + F (should hear beep) then ALT + B

    About the only reason to do a BIOS update is if your system is still under warranty.  If it is then now is a good time to get current with your BIOS versions.  Since there is always a slight risk in doing a BIOS update they shouldn't be done needlessly on a machine out of warranty.  Otherwise in reviewing the BIOS history for the 4600 model there is nothing listed that aided in drive detection problems.

    In order to flash the BIOS you will need to have a system that is bootable.  The latest and last BIOS release for your model is A12 and that can be downloaded by clicking here.   The BIOS upgrade format is a "universal" file that will run in Windows or DOS and from a hard drive, floppy or CD.  Some people have upgraded the BIOS by burning the file to a CD and then booting the system using a bootable CD like the Dell Resource CD.  Once the machine is booted up then switch CDs and run the BIOS upgrade from the command prompt.

    I'm assuming that the Dell Tech had you check the diagnostic lights and the lights were of no help. 

    One possibility for your problem is that you have a drive that is failing.   A bad hard drive or optical drive can cause problems for the rest of the drives connected to the system.  I would recommend run the Dell diagnostics on the system.  I would even try disconnecting a drive one at a time to see if the problem goes away.  If it does then suspect the disconnected drive as being at fault.  After each drive is disconnected I would clear the NVRAM as well to insure the system has correctly detecting the remaining drives.

  • 132

    0

    Posted July 22nd, 2006 21:00

    Thanks for the response.  As a matter of fact, they did not mention the lights, which I 'stumbled' across last night (and have since found the descriptions).  I hope that it isn't too late to save the data on the hard drive...
     
    Also, does 'flashing the BIOS' put the data on the disk at risk?
     
    and... after hitting ALT+E, I hear beeping (before ALT+F)... does that mean anything?
     
    Thanks
  • Majestic

    2 Intern

    •

    9371 Posts

    132

    0

    Posted July 23rd, 2006 11:00

    "As a matter of fact, they did not mention the lights, which I 'stumbled' across last night (and have since found the descriptions). "
     
    I'm assuming then you found the source of the problem as indicated by the lights?
     
    "Also, does 'flashing the BIOS' put the data on the disk at risk?"
     
    The BIOS flash will not effect the data stored on the hard drive.  Although bad BIOS flashes are rare, in a worse case scenario a bad flash will result in having to replace the motherboard.  That is why I mentioned doing the BIOS upgrades while the warranty was still active.
     
    "and... after hitting ALT+E, I hear beeping (before ALT+F)... does that mean anything?"
     
    The beep just indicates that the NVRAM was successfully cleared.  For some models this beep occurs after the ALT + E and for others it happens after the ALT + F.   I wouldn't worry as the method I gave you is proven to work on the 4600.