UNSOLVED

Noodell

updated

23 years ago

N

Noodell

5 Posts

0

10756

July 2nd, 2003 02:00

Freeze on Bootup, even in safe mode!!! Dim8200, winXPpro :(

Hi All,

I've had my dell dimension 8200 desktop for over a year, running winXP pro. Now it has a problem. I had to shut it off to move it, when I turned it back on it said something like "a check disk has been scheduled, and ran through it. I think it got through the 3 steps successfully, but then it hung at a grayish screen. I turned off by holding the power button in for 10 seconds or so.

I tried booting normally into windows, it says a disk check has been scheduled, went throught the 3 stages of disk check and said it completed each successfully, then did the system restart, then I got the XP logo, then the printer did its "wakeup noise", then the screen went blank and hung there.

I tried booting with last good configuration, it brings me to the 'disk check has been scheduled' screen, I hit a key to cancel the disk check, and then the system hangs at the line "Disk checking has been cancelled. Windows has finished checking the disk". \

I also tried booting into the various safe modes, system lists a bunch of files, then stops at multi(0)disk(0)rdisk(0)partition(2)\Windows|system32|drivers\agp440.sys. It hangs at this line for about 5 minutes, then comes up with the Dell screen, then the XP screen, then my printer makes its "wakeup noise", then I get a gray screen and it hangs there till I shut the system off.

Any ideas what's going on??? I can't get into my system at all!

Thanks in advance for your help!!

  • The_Namek

    2 Intern

    •

    2794 Posts

    330

    0

    Posted July 2nd, 2003 02:00

    QueenLucy,
    What has now become known as the infamous agp440.sys lockup/failure/error seems to have many possible causes. It can be the result of a hardware failure or simply a corrupt or buggy (read not digitally signed and/or is not on the Windows Hardware Compatibility List) device driver (usually video). Based on what you've tried already I'd recommend disabling agp440.sys as described in this Microsoft article.

    You can read more about the problem and what other people have done to correct and/or work around it here and here.

    Message Edited by The_Namek on 07-01-2003 10:41 PM

  • Noodell

    5 Posts

    330

    0

    Posted July 2nd, 2003 22:00

    Namek,

    Thank you for your reply. I have tried the Microsoft fix to no avail. Now onto the suggestions on the other links you gave me. It's distressing, this seems like a very tough problem with a myriad of things that may or may not fix it. I appreciate you pointing me in the direction of resources that might help. :)

    ...sigh...it's gonna be a long night.

  • The_Namek

    2 Intern

    •

    2794 Posts

    330

    0

    Posted July 3rd, 2003 03:00

    QueenLucy,
    I hope the information is useful in helping you resolve the lockup. Some computer problems are a major hassle to solve and unfortunately for you this is one of them.

    Good luck in your troubleshooting! 
  • Noodell

    5 Posts

    330

    0

    Posted July 3rd, 2003 12:00

    Well, it was a long night! I have taken out everything from the computer except the memory, powersupply, motherboard and hard disk. I swapped out a PCI video card for the AGP. I have reinstalled windowsXP over the top. Since the reinstall of windowsxp, now I it boots up, passes the annoying scandisk, then comes to a blue screen which reads: STOP: c000021a Unknown Hard Error. And hangs there forever.

    Anyone have any ideas on where to go from here? I don't know much about the xp recovery console. I can use it and get to my hard disk and see what's in there. Are there any diagnostics in there to help me see if the memory or motherboard is bad? I am not excited about buying new parts for this thing when I'm not sure what's bad!  At this point I'm thinking of trying to get a technician in here, while I still have some hair on my head! ;)

    Thanks in advance for your help!

    QueenLucy

  • The_Namek

    2 Intern

    •

    2794 Posts

    330

    0

    Posted July 4th, 2003 02:00

    QueenLucy,
    I believe I may be able to assist you further. Read this post and follow the procedure. Be sure to run the Dell 90-90 diagnostics on your hard drive before you go through the recovery console steps as you'll be wasting your time if it has failed. It might be a good idea to run Dell's 32 bit diagnostics on your RAM too.
  • Noodell

    5 Posts

    330

    0

    Posted July 4th, 2003 19:00

    Dear The_Namek,

    Thank you for your post! You led me to do lots with the diagnostic disk, which gave me more clues in my search for a resolution to this problem. I ended up testing everything, and the diagnostics are pointing to my hard drive. I'm alittle incredulous, because the check disk that runs when I start up the computer completes without errors and I can go into the recovery disk and do a chkdsk with no errors. But the hard disk check in the diagnostics yields the following 2 error messages.

    Test Errors
    IDE Disk 0 - Read Test                                     : Fail
      Status: Fail  Status Code: DOS DDG-D DISK 020 068
      Device: IDE_Disk_0  Test: Read_Test
      Release: 1087 Module(s): Disk
      Msg: Block 731783: Uncorrectable data error or media is write protected.

    IDE Disk 0 - Verify Test                                   : Fail
      Status: Fail  Status Code: DOS DDG-D DISK 260 068
      Device: IDE_Disk_0  Test: Verify_Test
      Release: 1087 Module(s): Disk
      Msg: Block 731783: Uncorrectable data error or media is write protected.

    I saw another post about these errors, a Dell representative suggested resetting the bios to default configuration (alt-f in bios), I did this but alas got the same error on bootup ....STOP: c000021a Unknown Hard Error.

    Any advice from anyone would be most appreciated. And The_Namek, thank you again for your great advice and troubleshooting tips that got me this far...I do appreciate you! 

    QueenLucy