UNSOLVED

jerrym59

updated

5 years ago

J

jerrym59

1 Rookie

•

10 Posts

0

1301

December 22nd, 2021 14:00

INSPIRON 3891 SSD update fails

 

New 3891, 12mb, core i5 11400 w/ uhd730, dvd/cd drive, 256 MB SSd, 1tb HDD, bios 1.3.1, Windows 10 (hm)

Running the SSD firmware update for Toshiba Solid-State Drive Firmware Update for KBG40ZNS128G/KBG40ZNS256G/KBG40ZNS512G/KBG40ZNS1T02  (ver 1041.0106, A00) gives  unsucessful insaller operation. The
Apparent pertinent part of log file seems to be:

 

Info: Opening Physical drive: SCSI0:p0

Info: CDB: 00 00 01 00 00 00 00 00 00 00 00 00 ec 00 00 00
Info: ATA Response [Error : 0x00] [Count : 0x0081] [LBA : 0x000000000081] [Device : 0x40] [Status : 0x50]

Info: CDB: 00 00 00 00 00 00 00 00 00 00 00 00 e5 00 00 00
Info: ATA Response [Error : 0x00] [Count : 0x0081] [LBA : 0x000000000081] [Device : 0x40] [Status : 0x50]

Info: Closing Physical drive
Info: Opening Physical drive: SCSI0:p2

Info: CDB: 00 00 01 00 00 00 00 00 00 00 00 00 ec 00 00 00
Error: ATA Response [Error : 0x04] [Count : 0x0003] [LBA : 0x000000eb1401] [Device : 0x00] [Status : 0x51]

Info: Closing Physical drive

Failed : 'No devices found'
>>> Command failed...
### Return code: 1 ###

Running installer .exe as ADMIN gives same thing. The drive works as no issue booting/running windows 10, etc.

I have 2 machines, the other one didn't fail and its log indicates that latest version already installed.

Any input would be appreciated and yes, this is already my 2nd post.

  • redxps630

    11 Legend

    •

    16434 Posts

    •

    83185 Points

    1098

    0

    Posted December 22nd, 2021 14:00

    Re: The drive works as no issue booting/running windows 10, etc.

    If it works fine I do not see a strong reason to update firmware.  I would consider test write/read speed of ssd using Crystal Mark and if results are within normal limit of spec, no worries.  The benefit of firmware update is spurious if ssd works fine.

  • RoHe

    12 Elder

    •

    45230 Posts

    •

    172625 Points

    1064

    0

    Posted December 23rd, 2021 17:00

    Do you actually have the problem this firmware update is supposed to fix?

    "Fixed the noise issue that occurs while playing music after the system resumes from idle state."

    How did you find that update? Did you use your Service Tag at the support page? (Don't post it here.) And was the little slider set so it only shows updates for this specific system?

    If PC is under warranty, you may want to contact Dell Tech Support for assistance...

  • jerrym59

    1 Rookie

    •

    10 Posts

    1053

    0

    Posted December 24th, 2021 05:00

    As these 2 3891's are brand new, I thought it prudent to get them up to date per support page's versions, regrdless of seeing issues or not. 

    Yes, not new to this, used service tags and "this PC" switch on support page for both machines. Both PC's SDD's pass diagnstics run from support page and work, so will move on and likely not attempt any more updates for SSD. (Although the other machine did not fail, simply said version already up to date). THX

  • RoHe

    12 Elder

    •

    45230 Posts

    •

    172625 Points

    1038

    0

    Posted December 24th, 2021 11:00

    @jerrym59 - If these PCs were purchased around the same time, it's possible both already have the latest firmware. You might want to run CrystalDiskInfo (free) on both PCs and compare firmware versions listed at top of the CDI screen for each of these SSDs.

    If the one has an earlier firmware, or the updater won't even say it has the latest version, you may want to contact Tech Support. Be sure to tell them one SSD says it's up-to-date and the other one errors out.

    When this PC goes off warranty and some critical SSD firmware update won't install, you'd have a problem.  IMO, better to sort it out sooner than...

  • jerrym59

    1 Rookie

    •

    10 Posts

    1017

    0

    Posted December 25th, 2021 08:00

    Thnking over (per redxps630) if I want to just move on as machine will likely keep going until it dies w/ current driver or go through Tech Support.

    Yes, there will likely be urgent updates coming for this and other drivers. I mainly updated just because PC's are new and at least wanted to start with current versions. I likely wouldn't have performed any updates in the future unless I felt a certain one was absoluely required based on past experience.

    There have been many while I've had my (now dying) XPS over the last 4 years and usually don't bother anymore with them if all is working. (I get there is risk).

  • jerrym59

    1 Rookie

    •

    10 Posts

    1004

    0

    Posted December 25th, 2021 14:00

    First part of ny post got lost--somehow. I ran crystaldiskinfo on both and there was agreement with what Device Mgr showed. 2nd PC that didn't fail update is on the current version per dell support page. (1st one is one that failed and is a version behind). Both work fine in use--so far.

    I regularly perform backups and always have.

    I didn't mean that I will wait until 1st PC SSD dies. I meant, can probably remain on that SSD FW version until COMPUTER dies and never give another thought.

    I may wind up returning one of them anyway as bought just because price to get 2 almost to good to pass up.

    THX.

  • RoHe

    12 Elder

    •

    45230 Posts

    •

    172625 Points

    1006

    0

    Posted December 25th, 2021 14:00

    Did you check firmware versions on both SSDs using CrystalDiskInfo?

    IMO, why wait until that SSD dies? You will likely lose everything stored on the SSD and then waste your time/efforts installing Windows and all your apps again. And if you don't back up personal files stored on that SSD regularly, those files will be gone forever.

    Your PC, your decision...