UNSOLVED

Jaymg

updated

1 month ago

J

Jaymg

1 Rookie

•

1 Message

•

4 Points

0

92

October 2nd, 2026 18:57

m15 R5 Ryzen, BIOS failed, black screen, power button flashing 2-1 red-blue

Hello everyone,

My laptop was working well until I decided to update my BIOS. The update failed due to the faulty battery in it which didn't pose an issue until now; I simply worked around it by keeping the AC plugged in. being the genius that I am, I made the decision to forcefully update the BIOS, and not only did the update fail, but I am now met with a totally black screen and the power button flashing 2-1 red-blue. I tried restarting and resetting to no avail with/without power, I made a FAT32 USB with BIOS on it and held ctrl+esc which didn't help, and the only progress i have made was holding down the power button for 18-33 seconds which revealed 2-4 red blinks.

A bit late now, but i have since changed the battery. Any tips that might mend my PC would help- I really don’t want to buy a new one because of my own stupidity.

(edited)

  • anne_droid

    6 Operator

    •

    2620 Posts

    •

    9651 Points

    0

    0

    Posted October 3rd, 2026 23:51

    Hi

     

    On an Alienware m15 Ryzen Edition R5, a repeating 2 red, 1 blue power-button pattern means processor (CPU) failure. In practice, it can be the CPU itself, a CPU power-delivery fault, or—less commonly—a system-board fault that presents as a CPU error.dell+1

     

    On the Alienware m15 Ryzen Edition R5, a repeating 2-red, 4-red power/battery LED pattern means memory (RAM) failure — the system detects RAM but cannot initialise/use it correctly.dell

     

    Do this first

    1. Unplug the charger and all USB/HDMI/SD accessories.

    2. Hold the power button for 30 seconds to drain residual power.

    3. Reconnect only the Dell AC adapter, then try to power on.

    4. If it still gives 2,4, open the bottom cover and reseat the RAM:

      • Disconnect AC and hold power 30 seconds again.

      • Remove/reinstall each SODIMM firmly until both side latches click.

      • Test with one module at a time, in each slot if possible.

    Narrow it down

    • If one stick alone boots: the other stick is likely faulty.

    • If either stick fails in one slot but works in the other: suspect the slot/board.

    • If both sticks fail in both slots: try known-good DDR4 SODIMMs compatible with the m15 R5; if it still gives 2,4, the memory controller/system board is the likely fault.

    • The m15 R5 uses removable DDR4 SODIMMs, so this is practical to test.

    If reseating does not fix it

    • Run Dell’s built-in ePSA/SupportAssist Pre-Boot diagnostics: power on and tap F12, then choose Diagnostics. Record any memory error and affected DIMM/slot.

    • Update BIOS only once the system can POST; if it cannot POST, a BIOS recovery is unlikely to resolve a genuine RAM fault, though it is worth trying if the code appeared immediately after a BIOS update.

    • If the same module fails repeatedly, replace it. If no module works in any slot, suspect the motherboard/memory channel rather than buying more RAM blindly.

    Dell’s service manual explicitly lists 2,4 as “Memory or RAM failure,” and recommends isolating the fault with a known-good DIMM.

     

     

    File Format: This file format consists of a BIOS Recovery image file. This file is used for the System BIOS Recovery process to recover a system from a corrupted BIOS.
    File Name: BIOS_IMG.rcv
    File size: 18.06 MB
    To ensure the integrity of your download, please verify the checksum value.
    MD5: 393611b49a370f2542aebd769ca7851c
    SHA1: fe1cfbc2eacd46bfb9771e9f6396ae8edf320f26
    SHA-256: de2e03c82f161e6f0c502d25d63cefbb8cb274bdcc00612888085312daae921c
     
    Updating the BIOS from DOS with UEFI boot mode enabled
    (Non-Windows users, Load Legacy Option Disabled)

    Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
    Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
    Note 3: Your system requires a restart after installing the BIOS. The restart can be deferred but must be completed to ensure that the update is installed.

    Installation
    1. Copy the downloaded file to a bootable DOS USB drive.
    2. Power on the system and then go to BIOS Setup by pressing the F2 key.
    3. Go to General > Boot Sequence > Boot > Boot List Option.
    4. Change UEFI to Legacy of Boot List Option.
    5. Go to Exit > Save Changes and reboot system.
    6. Press F12 and then select USB Storage Device and boot to the DOS prompt.
    7. Run the file by typing the file name.
    The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, the system restarts again.
    8. Go to BIOS Setup by pressing the F2 key and go to General > Boot Sequence > Boot > Boot List Option.
    9. Change Legacy to UEFI Boot Option.
    10. Go to Exit > Save Changes and reboot the system.
     
     
     
     

     

      Kind Regards  

                                         

      anne_droid

     

    User uploaded image

     

  • DashMark

    1 Rookie

    •

    10 Posts

    •

    39 Points

    8

    0

    Posted October 7th, 2026 13:05

    Ouch, that's a painful lesson but don't write the laptop off yet. Since the Ctrl+Esc BIOS recovery didn't work, try a full EC reset: unplug AC, hold the power button for a full 60 seconds, then plug back in and try the recovery USB again. Also worth removing the battery and CMOS battery for a few minutes if you're comfortable opening it up. If the 2-1 blink code persists, that's usually a motherboard/CPU fault and Dell support might still help even out of warranty. Good luck!