UNSOLVED

xphoto21x

updated

3 months ago

X

xphoto21x

1 Rookie

•

2 Posts

0

443

August 8th, 2023 11:00

Aurora R14, Nvidia RTX 4070, System Fan 3/4 failure

My current setup:

AMD Ryzen 5 5600X

32GB Ram

Nvidia RTX 4070 GPU

512GB SSD, 2TB HDD

750w PSU

 

I recently installed the Nvidia RTX 4070 GPU which previously had an AMD Radeon 6500XT. Upon boot up I am taken to the BIOS screen and it says, "System Fan 3, 4 failure, Error Code: 2000-0511". Ran diagnostic with no fix. I have confirmed the GPU fans run at startup, and have downloaded Afterburner to test the fans as well. Also there are no fans installed in System 3 and 4 on my computer. I've made sure everything is up to date across the board.

My PSU has two 8 and 6 pin connectors. I've tried both of them. Nothing else was touched while installing the GPU. During the Dell chat they said the 4070 wasn't compatible with my system? I asked why, but they wouldn't answer me. I ran MSFS 2020 on it with great success, and had my VR working flawlessly (VR didn't work on the Radeon 6500). Everything was smooth and much better than my previous setup, and I am very happy with the result. However, the fan error on startup is annoying.

(edited)

  • xphoto21x

    1 Rookie

    •

    2 Posts

    33

    1

    Posted August 8th, 2023 12:00

    Hey thanks for the link, and getting back to me. I guess upgrading components is a known issue with Dell. 

    When I first contacted support they stated the 4070 was compatible with my computer, but others have said it definitely is. I also assume they are just reading off a list of answers from a computer? 

     

    I wonder if installing a System 3,4 fan would alleviate the error? 

  • Vanadiel

    8 Professor

    •

    7094 Posts

    •

    29695 Points

    35

    0

    Posted August 8th, 2023 12:00

    Seems like they baked fan monitoring into the BIOS for AMD cards at least: Fan failures 

    I don't think there's a solution...

  • Cb129

    1 Rookie

    •

    7 Posts

    •

    23 Points

    0

    0

    Posted December 1st, 2025 23:00

    I had this same problem but i fixed it. My R14 didn't come with the two extra fans. So in order for it to stop giving me the error message, I had to buy two fans with a built in Tach and then install them. Power off the PC and unplug it for a few, install the fans, then boot it up and it'll register the new fans. 

  • user_b6f967

    1 Rookie

    •

    1 Message

    •

    2 Points

    0

    1

    Posted January 6th, 2026 22:16

    @Cb129​ How did you mount the fans?

  • Shane2506

    1 Rookie

    •

    1 Message

    •

    2 Points

    0

    1

    Posted January 11th, 2026 14:57

    Yes, How did you mount the fans? not any fan will fit in this tower. But I'm over this fan error. I think it causing other issues with how my pc runs as well.

  • Cb129

    1 Rookie

    •

    7 Posts

    •

    23 Points

    0

    0

    Posted January 11th, 2026 16:59

    @user_b6f967​ I ordered some long rubber fan mount screws. I used the holes that's already there in the metal grills on the top and the front. 

  • Cb129

    1 Rookie

    •

    7 Posts

    •

    23 Points

    0

    0

    Posted January 11th, 2026 17:08

    @Shane2506​ I just ordered two 120MM PWM fans. You have to make sure they have the speed sensor in them so the PC can determine how fast they're going. As long as they're decent high RPM fans then they'll work. I also used some long rubber fan mount screws and mounted them using holes that were already there in the metal grill on the top and the front. 

    (edited)

  • kumuho

    1 Rookie

    •

    7 Posts

    0

    1

    Posted January 21st, 2026 06:02

    @Cb129​ Will the pin a sign on the PWM connector of the aftermarket fan be okay without any conversion?

  • Cb129

    1 Rookie

    •

    7 Posts

    •

    23 Points

    0

    0

    Posted August 10th, 2026 13:10

    @kumuho​ sorry for the late reply but yes. I assume by now you've got it all sorted.