So long story short: I purchased a dock WD19TB which makes an electrical noise when connected to my laptop. After a discussion with Dell support, I was advised to try a clean boot by deactivating non microsoft services at start-up.
I entered MSCongif, I unchecked the box load startup items, then I went to boot tab and I checked Safe Boot -> minimal.
After this I restarted the laptop and the message is: something happened and your pin isn't available -> I don't get the PIN enter window at all.
The windows hello and fingerprint login are not working.
The reset pin option not working.
Boot in safe mode not working (simple, with command prompt or with network)
I made a windows boot stick and started in boot mode from the stick.
Repair windows startup not working.
Control+Alt+Del not working
Started command prompt from the boot stick -> typed start msconfig -> not found.
I would reinstall the windows but I left on the desktop some videos to prepare for editing and I can't reinstall windows without losing everything. The upgrade windows option will not work from the boot stick.
If you are booted into the command prompt type the command bcdedit. It will give you a listing with sections. In the first section, you will see a term inside curly brackets which will be either current or default. Make note of what this shows because you have to use it in the next command.
Now you want to remove the safeboot entry in the listing for that OS. So you use the command below and make sure and use the curly brackets. If using default or current doesn't work, try the other one.
bcdedit /deletevalue {default} safeboot
Close the command prompt and boot your system. It should boot back into Windows. I am hoping your did not check a box which would have not allowed any services to start..
A clean boot is not the same as Safe Mode.. Safe mode will require a password if the PIN is not available. If you can't enter your password either, you may have to boot to a USB drive with the Install media or a recovery drive, and get into the command prompt.
Let us know if you can do that. There is a command you can use to turn off Safe Mode.
Saltgrass
6 Operator
•
4328 Posts
•
15932 Points
242
0
Posted September 28th, 2021 06:00
If you are booted into the command prompt type the command bcdedit. It will give you a listing with sections. In the first section, you will see a term inside curly brackets which will be either current or default. Make note of what this shows because you have to use it in the next command.
Now you want to remove the safeboot entry in the listing for that OS. So you use the command below and make sure and use the curly brackets. If using default or current doesn't work, try the other one.
bcdedit /deletevalue {default} safeboot
Close the command prompt and boot your system. It should boot back into Windows. I am hoping your did not check a box which would have not allowed any services to start..
-------------------------------------------------------------------------------------
Windows Boot Manager
--------------------
identifier {bootmgr}
device partition=\Device\HarddiskVolume6
path \EFI\MICROSOFT\BOOT\BOOTMGFW.EFI
description Windows Boot Manager
locale en-US
inherit {globalsettings}
flightsigning Yes
default {current}
resumeobject {70c41008-db6d-11eb-8fe5-831dca2ea2b6}
displayorder {3afcb1d7-1c11-11ec-bcaf-bb28f99cb367}
{70c41009-db6d-11eb-8fe5-831dca2ea2b6}
{current}
toolsdisplayorder {memdiag}
timeout 30
Windows Boot Loader
-------------------
identifier {current}
device partition=C:
path \Windows\system32\winload.efi
description Windows 11 Beta
locale en-US
inherit {bootloadersettings}
displaymessageoverride Recovery
recoveryenabled No
isolatedcontext Yes
flightsigning Yes
allowedinmemorysettings 0x15000075
osdevice partition=C:
systemroot \windows
resumeobject {70c41008-db6d-11eb-8fe5-831dca2ea2b6}
nx OptIn
safeboot Minimal
bootmenupolicy Standard