Captain Marvel

updated

4 years ago

CM

Captain Marvel

1 Rookie

•

16 Posts

0

2148

December 17th, 2022 13:00

XPS 8950, unable to do a clean install of Windows

When I got to the step where I should be able to select the disk where I want Windows to be installed, there were no disks listed, not even the hard drive. The message was asking for the disk driver. Apparently Windows doesn't include disk drivers for Dell computers? What do I need to do to be able to install Windows?

Thanks for your help.

  • Captain Marvel

    1 Rookie

    •

    16 Posts

    1425

    0

    Posted December 25th, 2022 12:00

    When I first got the computer I removed the installed M.2 card. I put in a 2TB card and tried to install Windows on it. That's where I had the problem discussed above. I solved the problem by taking the OEM M.2 card and put it in a USB enclosure and connected it to my laptop. I then connected another enclosure with my new blank 2TB card and cloned the OEM card to the 2TB card. I the installed the 2tb card in the DELL and it booted up just fine and has been running without any problems.

    Thanks to everyone for the advice and suggestions.

  • NJDave

    2 Intern

    •

    406 Posts

    1516

    2

    Posted December 17th, 2022 14:00

    I'm guessing that SATA operation is switched to "RAID on" in the BIOS. This is where the request for a driver comes in, since the required Intel Rapid Storage Technology driver isn't in the Windows installation media. Presuming you don't want to set up RAID operation, easiest fix is to change the setting to AHCI mode before installing.

  • Prasad38

    1 Rookie

    •

    3 Posts

    1508

    0

    Posted December 17th, 2022 14:00

    Hi, I had similar problem with my PC in past, I download the recovery software from dell site on a USB and by using F12, booted from USB and installed it.

  • JOcean

    11 Legend

    •

    12621 Posts

    •

    69453 Points

    1513

    0

    Posted December 17th, 2022 14:00

    @NJDave is spot on with advice. If what is suggested does not help then, assuming you have more than one drive, disconnect all drives except the drive you want to install Windows on. If that does not help and if the drive you are trying to install Windows on is an M.2 SSD then have a look at this YouTube video. You may need to add the Intel Rapid Storage driver to the Windows installation flash drive.

    I am not a Dell employee...I am forum volunteer

    Serious work on an E5430 and constantly building and working on an i5-6500 Desktop

  • Captain Marvel

    1 Rookie

    •

    16 Posts

    1477

    0

    Posted December 18th, 2022 21:00

    I checked the bios and it was set to AHCI.

  • NJDave

    2 Intern

    •

    406 Posts

    1471

    0

    Posted December 18th, 2022 22:00

    @Tesla1856 has a great point about running a DiskPart clean operation.

    To back up, though: none of us has yet asked you to specify what storage is in the system, where you're trying to install Windows, what version of Windows. Could you please do so?

    Does the storage in the system appear in your Storage configuration in BIOS? Does it pass pre-boot diagnostics?

    If so, if you don't currently have Windows available on the system (probably?) and assuming you're trying to install from standard Microsoft install media (e.g. built from the media creation tool) you can break into Windows installation and run DiskPart from a command window (see this). I don't think you want to create a partition as shown in the illustrations; just a "clean" operation on the drive where you want to install Windows should suffice -- though a subsequent "convert gpt" to initialize the drive probably couldn't hurt.

  • Tesla1856

    10 Wizard

    •

    18086 Posts

    •

    71947 Points

    1474

    1

    Posted December 18th, 2022 22:00


    @Captain Marvel wrote:

    I checked the bios and it was set to AHCI.


    That is fine.

    You don't say if it's a M.2-NVMe or a 2.5in-SATA ... but I don't guess it matters as long as it's the only disk connected at install time (you can re-connect any other drives later).

    If it's still not appearing, be sure it's completely erased (no partitions and un-initialized/raw). You can do that with a proper Diskpart Clean procedure.

    Dell Rockstar

    Microsoft Windows and Apple iOS Developer (Retired)
    - Like many of you, I can appreciate a good game-engine.
    - I answer questions here, but I'm not a Dell employee.
    - Consider giving posts you like a "thumbs-up"
    - Posting models-numbers and software versions speeds trouble-shooting.
    - Click "Mark as Accepted Answer" on any post that answers your question best.