Oldcaliforniakid

updated

6 months ago

O

Oldcaliforniakid

1 Rookie

•

10 Posts

•

8 Points

0

696

April 23rd, 2026 15:06

XPS 8920, cloned HDD OS doesn’t show as boot option in BIOS

My 512 GB SSD with the OS on it is full. I cloned the SSD to a 2TB HHD I installed in the tower with 4DDIG.

When I go into the boot section of BIOS to change the boot sequence, there is no listing for the new HDD drive.  This is what is there:


Option #1 (Windows Boot Manager)

Option #2 (Onboard NIC (IPV4 PXE)

Option #3 (Onboard NIC (IPV6 PXE)


What am I doing wrong?

(edited)

  • Oldcaliforniakid

    1 Rookie

    •

    10 Posts

    •

    8 Points

    0

    0

    Posted April 25th, 2026 16:37

    @Chino de Oro​ Thanks. I used these steps:

    1. Installed 1TB SSD new drive in the second slot

    2. Cloned the OS system and all other files from the C Drive to the new drive

    3. Formatted and Initialized the old drive to use as storage

    4. Works great. Very fast and tons of room for everything

    5. Without upgrading my C Drive, I was unable to view the hundreds of photo files in Photoshop. They only appeared as icons because of the lack of disk space. Opening each one individually to see which photo it was took too much time and effort. They also only appeared as icons in File Explorer because of the lack of disk space on the C Drive.

    6. I used 4DDiG software to do the cloning and the cmd in shell to use diskpart to clean the original C Drive.

    Thanks for everyone's help. I love my computer again...

  • ejn63

    12 Elder

    •

    31866 Posts

    •

    156343 Points

    0

    0

    Posted April 23rd, 2026 16:25

    The answer requires more information:

    1.  What was the default boot originally?  Windows boot manager is the usual default.

    2.  What did you use to make the clone?

    3.  Did you boot the system at any time with both the cloned drive and the original in the system?

  • Oldcaliforniakid

    1 Rookie

    •

    10 Posts

    •

    8 Points

    0

    0

    Posted April 23rd, 2026 16:42

    @ejn63​

    1. That is the original default boot that I listed with Windows boot manager as option #1

    2. I used Tenorshare 4DDiG to clone

    3. I have continued to boot the system with the C Drive from the SSD that came with the computer when I bought it a couple of years ago.

  • redxps630

    11 Legend

    •

    16434 Posts

    •

    83185 Points

    0

    0

    Posted April 23rd, 2026 16:45

    You are not doing anything wrong but in UEFI you don’t see individual boot device listed in boot priority. WBM was set up to be linked to original ssd/EFI partition boot mgr.  to boot from her assuming it is cloned correctly you need to WBM setup to efi partition of hds

  • Oldcaliforniakid

    1 Rookie

    •

    10 Posts

    •

    8 Points

    0

    0

    Posted April 23rd, 2026 16:51

    @redxps630​ Thanks. That sounds logical. How to I find WBM on my computer to change the setup to EFI the partition of hard drives?

  • ejn63

    12 Elder

    •

    31866 Posts

    •

    156343 Points

    0

    0

    Posted April 23rd, 2026 19:22

    @Oldcaliforniakid​ 

    Re-clone the drive.  This time, make sure you shut down the system immediately thereafter.  Remove the original drive and install the replacement in its place.  The system should then boot from the new drive.  Once you've done that, you can reinstall the original drive and use it for storage.

    You can't allow the system to boot with both the original drive and the clone in place -- once you do, the clone is then set as a secondary and only the original drive will be bootable.

    That said, if you're replacing a speedy SSD with a spinning hard drive, bear in mind you will see a major decrease in system performance.    You may be better off installing the hard drive as a secondary and moving your data to it -- and if still more space is needed, uninstall less demanding applications from the SSD and install them to the new hard drive.

    (edited)

  • Oldcaliforniakid

    1 Rookie

    •

    10 Posts

    •

    8 Points

    0

    0

    Posted April 23rd, 2026 19:45

    @ejn63​ Thanks. Will use the HDD as large photo storage and get a larger SSD.

    So, if I put a larger SSD in the spare slot, clone the OS C Drive to it, should I just shut down the computer normally, pull the older C Drive, reboot, hoping it will recognize the new larger SSD? Should I leave it in the second slot or now put it where the original one was?

  • ejn63

    12 Elder

    •

    31866 Posts

    •

    156343 Points

    0

    0

    Posted April 23rd, 2026 20:03

    First be sure you have two SSD slots -- some desktops, particularly older ones only have one.  As long as you remove the original drive before booting the system for the first time after cloning, it should be straightforward.   You may want to turn off secure boot in setup (F2 at powerup) before doing so.

  • redxps630

    11 Legend

    •

    16434 Posts

    •

    83185 Points

    0

    0

    Posted April 23rd, 2026 21:43

    If I do the cloning, I would create system image of ssd using an external usb hdd, then replace ssd with 2tb hdd, boot pc from a small recovery usb drive, connect external hdd to pc, restore system image to 2tb hdd, works like a charm. Pc will boot from hdd not evening noticing you had swapped the physical drive

  • Oldcaliforniakid

    1 Rookie

    •

    10 Posts

    •

    8 Points

    0

    0

    Posted April 23rd, 2026 22:18

    OK. Now I’m getting confused. I understand cloning the C Drive to an external drive via USB but don’t understand booting the pc from a small recovery USB drive. Where does that recovery drive come from?