UNSOLVED

dirksterg30

updated

18 years ago

0

3402

October 5th, 2008 18:00

Vista install issue

The 160GB SATA hard drive on my Inspiron 1720 laptop recently died. I purchased a 250GB SATA drive to replace it. I installed the new drive, and am reinstalling Vista Home from the CD that came with my system.

 

Vista seems to go through the installation process fine, until it comes to the "Completing installation" step. I don't think the computer froze up, as the screen is updating (the mouse works, and the 3 dots after the words "Completing installation" are displaying properly as well - first one dot, then 2, then 3, then none and so on). The progress bar at the bottom has been at about 3/5ths complete for at least 20 minutes. The HD light comes on intermittently, but only for about a second at a time. Pressing the ESC key says "setup cannot be cancelled at this point. Doing so could leave your computer in a potentially unusable state."

 

If I turn off the power & restart, Vista never gets past the green startup bar. If I start up in safe mode, the last line that shows up references crcdisk.sys, and it never goes into Windows.

 

I have tried installing Vista a number of times, with the same result each time. Diagnostics can find nothing wrong with memory, HD, etc. I even formatted the HD before the last attempt, and the results are the same.

 

Any ideas what's going on?

  • Sofu

    984 Posts

    247

    0

    Posted October 5th, 2008 20:00

    You need to download the SATA driver from here on another computer and save it to a CD-R or DVD-R. Do a clean install of Windows Vista. During the installation watch carefully for the message at the bottom of the screen when it prompts to "press F6 to load drivers". Install the SATA driver from the disk and continue.
  • Sofu

    984 Posts

    247

    0

    Posted October 6th, 2008 23:00

    Glad to be of help:smileyhappy:
  • 247

    0

    Posted October 6th, 2008 23:00

    John, 

     

    Thanks for the tip. It was very helpful.

     

    Dirk

    Message Edited by dirksterg30 on 10-06-2008 07:02 PM
  • twokatmew

    5 Posts

    247

    0

    Posted October 30th, 2008 20:00

    This is sooooo bizarre.  I have a 1520 with the original Fujitsu 160GB SATA drive in it.  I have reinstalled this machine from scratch a couple times and *never* even downloaded the MATRIX driver pointed out in this thread.  (I reinstalled the first time, because I wanted to get rid of all the crud trial software that comes installed on these machines, and the second time, I wanted to do a fresh install so I could upgrade to VistaHP32 SP1 before connecting to the network, installing any other software, etc.

     

    This time, my machine would boot into Windows, but then it would hang as if the CPU were stuck at 100%.  Of course, I couldn't run Task Mgr to find out.  I *could* boot into safe mode initially.  After a few times of that, however, the machine started to hang (when booting safe mode) at the "crcdisk.sys" Please wait.... nightmare.  Trying to boot Windows normally just sticks at the little moving icon (bottom screen) where it shows Windows loading.  But it will do that forever.

     

    Anyway, as I've been working with computers & networks for over 20yrs, I did quite a bit of troubleshooting, and I searched all over the 'net (before coming here, silly me) and found all sorts of mostly laptop owners suddenly getting this "crcdisk.sys" hang.  It's been blamed on the Intel wireless 3945 card (which is installed in my machine), USB drivers, and a slew of other things.

     

    Two Dell techs have me reseating the hard drive & RAM, swapping RAM chips (2GB in DIMM-A slot and 1GB in DIMM-B slot), with nothing but the same results.  Right now I'm at my wits end, so I'm very glad to find this post I have just downloaded the MATRIX driver and put both the expanded and *.EXE file on a CD and hopefully manage to get Vista installed again.  (My machine came with Vista vanilla, no SP1.)

     

    I'm crossing my fingers that this will work.  However, my question is, if this makes the difference, why have I been able to install Vista (from Dell's same OEM disc) w/o the MATRIX driver twice before?

     

    Well thanks for the tip, off I go to try a Vista install using the MATRIX drivers.

     

    Regards, and I'll post back with results, hopefully success and a big thank you!

  • Sofu

    984 Posts

    247

    0

    Posted October 31st, 2008 00:00

    twokatmew:

     

    I hope you are successful.

    The Intel Matrix Storage Manager is used to install or update the Intel Serial ATA (SATA) Advanced Host Controller Interface (AHCI) Controller Driver. Assuming that it solves your problem, I assume that the Windows Vista installation process found the need to reinstall or change the version of the AHCI Controller Driver.

  • twokatmew

    5 Posts

    247

    0

    Posted October 31st, 2008 01:00

    John, thank you sooooooooooooo much!  That MATRIX driver was exactly what I needed to get Vista reinstalled on my 1520!  If I hadn't seen it with my own eyes (having reinstalled twice w/o ever using that driver), I wouldn't believe it.  Seems impossible, but I'll happily take your explanation for it.  (The other is that I'm losing my mind.....)  :smileywink:

     

    Too bad the Dell techs didn't have this information at their fingertips.  I think next time I'll start with the Dell forums when I have a problem that stumps this old computer pro'.  :smileyvery-happy:

     

    Even SP1 installed w/o a hitch.  So now it's off to begin the long reinstall and config of all my software.  But I now have a speedy and functional machine again.

     

    BTW, from your list, our machines are exactly the same, 'cept for some reason I got 3GBs of RAM.  IIRC, there was a deal where they threw in an extra GB for ordering two.....

     

    Anyway, many, many thanks and best regards!!

     

     

    Message Edited by twokatmew on 10-30-2008 09:18 PM
  • Sofu

    984 Posts

    247

    0

    Posted October 31st, 2008 03:00

    twokatmew:

    You're most welcome. The main thing is that it worked:smileywink: