UNSOLVED

iniko

updated

13 years ago

I

iniko

8 Posts

0

935

February 11th, 2014 10:00

VNX5100 and storage pool for VMware

Hi All,

i'm configuring a new VNX5100 for use with VMware 5.5.

VNX is configured with 30 600 Gb 15k disks (15 in DPE and 15 in DAE).

My idea is to configure a RAID group with 4 disks (vault) and a single storage pool in RAID 6 (14+2) with the remaining 26 disks.

Could be this a good solutions for a balance between performance and available space ?

Thank you so much!

  • iniko

    8 Posts

    489

    0

    Posted February 11th, 2014 11:00

    Sorry, I misunderstood your sentences and no, I don't want to use vault for intensive I/O.

    Thanks again

    Il giorno 11/feb/2014, alle ore 20:25, "dynamox" > ha scritto:

    ECN

    VNX5100 and storage pool for VMware

    reply from dynamox in VNX Support Forum - View the full discussion

  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    489

    0

    Posted February 11th, 2014 11:00

    no worries, good luck.

  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    489

    1

    Posted February 11th, 2014 11:00

    you are burning a lot of space to parity plus 6x write penalty. Why not something more common (4+1 Raid-5) ..there are other options for RAID-5 but i like this option better because it keeps raid groups relatively small so they rebuild faster and less opportunities for double drive failure. I would configure 4 vault + 25 pool ( it will create 5 x 4+1 private raid groups) and 1 hot spare. Should give you around 8.5 usable capacity in the pool.

  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    489

    1

    Posted February 11th, 2014 11:00

    no, the first 4 drives are vault ..you can't add them to a pool. These drives will be provisioned into a raid group so there will be some space left but typically you don't want to put any i/o intensive workloads on those drives.

    1 drive will be dedicated as a hot spare

    that leaves you with 25 drives, you will use all 25 drives and create one pool.

  • iniko

    8 Posts

    489

    0

    Posted February 11th, 2014 11:00

    Thanks Dynamox, so i could create a raid group with first 5 disk and 5 pools with raid 4+1..right?

    Il giorno 11/feb/2014, alle ore 20:12, "dynamox" > ha scritto:

    ECN

    VNX5100 and storage pool for VMware

    reply from dynamox in VNX Support Forum - View the full discussion

  • Roger_Wu

    6 Operator

    •

    4025 Posts

    489

    0

    Posted February 11th, 2014 17:00

    You are using SAS disks (600GB 15K), so RAID 5 is Ok. If SATA disks (1/2/3TB, 7.2K), then RAID 6 will be better. SATA disks usually have higher failure rate and unrecoverable read error rate than SAS disks. RAID 6 will give you more protection than RAID 5 does, but for SAS disks RAID 5 is Ok since you also want performance.

  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    489

    1

    Posted February 11th, 2014 19:00

    Roger W. wrote:

    RAID 6 will give you no more protection than RAID 5 does

    Is that so ?

  • Roger_Wu

    6 Operator

    •

    4025 Posts

    489

    1

    Posted February 11th, 2014 19:00

    Sorry, it's a typo. It should be "RAID 6 will give you more protection than RAID 5 does".

    Thanks for the correction.