UNSOLVED

Kongfupanda

updated

12 years ago

K

Kongfupanda

12 Posts

0

3368

March 9th, 2015 08:00

unable to initialize vnx5200,failed to discover cs1

Hi team,I got a new vnx5200,unified storage. Got issue to initialise it,can help please ?.I have all utp and fc connected and power on dpe,2 blade enclosures,cs0,then cs1. Mgmt ports from cs0&1 to a small switch, same as my laptop.laptop firewall disabled,WiFi disabled. I ran via, it found cs0 Mac IP but complain unable to find the cs1 in a dual control station sysytm. The seconardy CS shows grey which is must to fill in before I am allowed to continue. Any advice how to fix this ? I power off all and boot again, cs1 boot up ,after 20min ,then I boot up cs0. The spa and spb got label with IP for them, 128.221.252.200 etc. I guess those are factory default. I think it is necessary to use CS to configure all though I can access spa and b via USM AND WEB UI . please advise. Thanks !

  • smarti2

    214 Posts

    1129

    1

    Posted March 9th, 2015 10:00

    Sounds like a cabling fault to me. Check the cables between all the components again against the VNX5200 Unified Install guide. There should be a very short cable that goes between both Control Stations.

    Put a serial cable into CS1 and check it is booted. If you can log in try pinging CS0 on it's internal IP address which you can see in the /etc/hosts file.

  • Kongfupanda

    12 Posts

    1129

    0

    Posted March 9th, 2015 19:00

    Hi Smarti,Thanks for much for advice. Even I connected the short UTP cable from cs0 to cs1 I still got the same error with my VIA. "VNX installation assistant cound not detect the secondary control station on this dual control station system. check the external entwork cable connected to secondary control station and click retry search button"

    A few points , can you help verify if I did correctly?

    1. I didn't use the extension cables to blade encl0 MMB ports , I only use my  normal UTP cables as they are very close and I don't think it's necessary to use extension cable though the installation guide mentioned extension cables

    2.  CS1 and CS0 mgmpt port to public LAN, I connected both to the switch as same as my laptop. I read an article saying I should not connect service ports of SPA and SPB to a switch at same time,but I guess it's ok to to connect both for cs0 and cs1. Hope I understand correctly..

    3. I didn't connect modems on CS0/CS1, I assume this is not related to my issue

    so basically I did these connections as below :

    1. cs0 B mgmt --blade 3 port 1

    2. cs0  port 2 -- blade 2 port 1

    3. cs0 mgmt (right port) -- switch(public LAN)

    4. cs0 cs port1 --- cs1 cs port 1

    5. cs1 mgmt -switch (public LAN)

    6 cs1 B mgmt -- Blade Encl 0 mmb port 2 on blade 3

    7 cs1 A port 2 -- blade 2 port 2

    8. blade 2 MMA port 0 -- SPA Mgmt

    9. blade 3 MMB port 0 -- SPB mgmt

    and then four FC cables between enclosure0 and DPE

    anything I did wrongly? thanks so much!

  • smarti2

    214 Posts

    1129

    0

    Posted March 10th, 2015 02:00

    Cabling seems ok. Is the switch port for CS1 enabled?

    Did you try the serial cable into CS1 I mentioned?

  • Kongfupanda

    12 Posts

    1129

    0

    Posted March 10th, 2015 04:00

    it is a small four port switch and no port issue on the switch I believe. Serial not yet as my win7 HP laptlaptop can not recognise my no name generic USB serial converter ....

  • Ybfx

    24 Posts

    1129

    1

    Posted March 10th, 2015 07:00

    hi,

    please try to boot cs0 1st then wait 5/10 min and boot cs1...restart VIA...

    rgds

  • Kongfupanda

    12 Posts

    1134

    0

    Posted March 10th, 2015 08:00

    I did try to boot cs1 20min after I boot up cs0 while not working. Via closed and run again for a dew times too. Is there a way to reset everything to factory default ? Could it resolve the issue ? Thanks

  • Kongfupanda

    12 Posts

    1134

    0

    Posted March 10th, 2015 08:00

    I tried remove VIA and install v8.1.3 VIA but still same issue. Then I downloaded UnisphereInitTool-Win-32-x86-loc-1.3.3.1.0072-1 and installed it. it tried to discover but finally gave me this "No unitiallized sotrage systems were discovered "   and there is a CETV2xxxxx8 system shows in "initialised system" window. I chose the initialised one and go next, got " the storage processors in the targeted storage system have a inconsistent IPv6 settings and cannot currently be configured with this tool Possible reasons are 1. processors is still booting...2 the workstation does not have network connections to both storage processors."  what you advise?thanks

  • Kongfupanda

    12 Posts

    550

    0

    Posted March 10th, 2015 09:00

    Thanks. after I found the one initialised system with storage system initialisation wizard and hit next, it shows me that SPB hostname  blank and IP 0.0.0.0 IPv6 disabled. Will try to get another laptop to try the serial again....many thanks!

  • smarti2

    214 Posts

    1134

    1

    Posted March 10th, 2015 09:00

    You really need to get a serial cable into the 2nd control station and see what state it's in.

    It should have a message such as waiting for VIA or something like that.

    There is a procedure to reset everything but it's pretty complicated if you aren't familiar with how VNX installation works.

    You should contact EMC support by the sound of things.

  • Ybfx

    24 Posts

    1134

    1

    Posted March 10th, 2015 09:00

    best is to have a serial connection to check if both CS are in VIA step...

    yes, you could install it with only CS0 and perform after the Add secondary CS procedure...