UNSOLVED

boyerr

updated

15 years ago

B

boyerr

12 Posts

0

3007

September 27th, 2011 07:00

NSX to VNX replication

All:

have several NSX platforms and customer just recently purchased several new VNX 7500 frames. Attempting to create / test replication between the 2 and am unable to establist data mover interconnects between them.  IS this even possible since VNX is at 7.0 code and the NSX is at 6.0.41-4...?  is there a white paper / solution availalble to review for this type of environment.  At some point down the road we will need to begin to move data from frame to frame, but right now we just want to test moving small shares from frame to frame 

thanks in advnace...

  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    613

    0

    Posted September 27th, 2011 07:00

  • boyerr

    12 Posts

    613

    0

    Posted September 27th, 2011 08:00

    thanks, it is much appreciated. 

  • boyerr

    12 Posts

    613

    0

    Posted September 27th, 2011 09:00

    OK..so i have followed these steps to the letter and cannot get it to create a DM interconnect.  From the source celerra I can ping the destindation CS and DM, time skew is dead on, and I can nslookup both CS and DM from the source frame CS

    any thoughts / ideas..???  I have setup several DM interconnects between NS and NSX we have here without issue, just cant do the same between the VNX and the NSX.

    thanks in advance

  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    613

    0

    Posted September 27th, 2011 20:00

    do you get an error or it simply times out ?

  • boyerr

    12 Posts

    615

    0

    Posted September 28th, 2011 06:00

    gives me Cannot access any Data Movers on the remote system NSX, check if the data movers on the specified rmeote system are accessable ( they are )( i can ping between frames and NSlookup ) Ensure the time difference between systems is less than 10 minutes ( both use the same NTP servers so are identical ) and ensure the passphrase between the 2 systems is correct.

    I even tried doing this from VNX frame to another VNX frame and received the same issue.  All licensing appears to be in order and is enabled...

    crazy that this wont configure.....!!!  

  • Rainer_EMC

    6 Operator

    •

    8645 Posts

    615

    0

    Posted September 28th, 2011 08:00

    which 7.x code exactly ?

  • boyerr

    12 Posts

    615

    0

    Posted September 28th, 2011 10:00

    NAS Ver 7.0.13-1

  • Rainer_EMC

    6 Operator

    •

    8645 Posts

    615

    0

    Posted September 28th, 2011 11:00

    Sound like an issue with using local accounts to establish the interconnects.

    I would suggest to look at the release notes and knowledgebase to understand the workarounds.

    Also use the CLI – its much easier to troubleshoot. And look at the logs for the actual error messages.

    If you’re not comfortable with the CLI then support can help you through a service request.

    Its probably easier to upgrade the VNX to the latest 7.0.35 release – then you can create a multi-domain

    setup where single sign-on and local accounts work – makes it easier to use Replicator.

    The new UniSphere white paper on Powerlink has the details.

    Rainer

  • boyerr

    12 Posts

    615

    0

    Posted September 28th, 2011 12:00

    OK....i was able to create the interconnects via the CLI and they "seem" to validate but errors / alerts appear.

    states something about HTTP communication not permitted and states the passphrase or time skew is off between frames. ( which I know neither is wrong ).

    i am continuing to review and test via the CLI  I will update you with my findings / results...

    thanks for all the help..!!

  • Rainer_EMC

    6 Operator

    •

    8645 Posts

    300

    0

    Posted September 29th, 2011 02:00

    Did you check both control station and data mover clocks ? they are independent

    Shouldn’t be too hard to figure out with the complete error messages and the knowledgebase.

    Any reason you don’t just open a service request ?

    Rainer