UNSOLVED

joe_cascanette

updated

17 years ago

0

3188

November 17th, 2009 10:00

SYMCLI to find out how many disks are installed and configured

I am looking for a way to find out how many physical disks are installed in my DMX3, and how many are in fact configured for use with the Symm. Is this possible by the command line or do i have to get EMC to dial into the array to tell me this?

I took control of a DMX3, and i am not physically able to access this array. I do have access to ECC, however this one array is not displaying anything related to disk slots available (tab is there, but no entry what so ever). So I would like to find out how many physical disks are installed, and the number of slots available, as well as obtain if all the disk that are installed in the array are configured within the Symm for use. I have a feeling that there are some disks installed that were never bin'd up for use with in the array.

Thanks

Joe

  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    1577

    1

    Posted November 17th, 2009 10:00

    right ..if it's not in the bin file, symcli will not show it.
  • HankDorsett

    66 Posts

    1577

    1

    Posted November 17th, 2009 10:00

    You can use symdisk command to view all disk installed on the array.

    symdisk -sid XXXX list

    Output:

    Disks Selected               : 912

                                                            Capacity(MB)
    Ident  Symb Int TID Vendor     Type       Hypers   Total    Free    Actual
    ------ ---- --- --- ---------- ---------- ------ -------- -------- --------
    DF-1A  01A    C   0 SEAGATE    C300LPF        73   286102     4610   286102
    DF-1A  01A    C   2 SEAGATE    C300LPF        74   286102     4267   286102
    DF-1A  01A    C   4 SEAGATE    C300LPF        75   286102     1025   286102
    DF-1A  01A    C   6 SEAGATE    C300LPF        74   286102      128   286102
    DF-1A  01A    C   8 SEAGATE    C300LPF        76   286102     3830   286102
    DF-1A  01A    C   A SEAGATE    C300LPF        76   286102     1019   286102
    DF-1A  01A    C   C SEAGATE    C300LPF        74   286102     2053   286102
    DF-1A  01A    C  10 SEAGATE    C300LPF        76   286102     1019   286102
    DF-1A  01A    C  12 SEAGATE    C300LPF        76   286102     1019   286102
    DF-1A  01A    C  14 SEAGATE    C300LPF        76   286102     1019   286102
    DF-1A  01A    C  16 SEAGATE    C300LPF        74   286102        1   286102
    DF-1A  01A    C  18 SEAGATE    C300LPF        75   286102     1025   286102

    If you see this, 0 hypers and no free space, it's more than likely a hot spare.

    DF-1A  01A    C  1A SEAGATE    T300R10         0        0        0   286102

    This disk has only one hyper configured, GK I htink, and still has about 280GB available to be configured.

    DF-16C 16C    C  19 SEAGATE    T300R10         1   286102   286096   286102

  • 1577

    0

    Posted November 17th, 2009 10:00

    I found a part of my answer.

    symdisk -sid #### list > c:\symdisk.txt

    At the top it show me the number of disks, but i am sure this is only what is configured in the Symm. So if there were physically more disks installed, then this output many not show me this.

  • GAD1

    12 Posts

    1577

    0

    Posted November 24th, 2009 03:00

    Not sure if this is what you are after, but I use this command:

    symcfg -sid XXX list -v

    It will show the following (Note: I only pasted part of the output):

        Number of Configured (Sym) Devices   : xxxxx
        Number of Visible (Host) Devices     :     x

        Number of Configured Actual Disks    :  1190
        Number of Configured Hot Spares      :    10
        Number of Unconfigured Disks         :     0
        Maximum number of hypers per disk    :   255