What Raid controller card do you have installed? I am not sure if you system comes with a built-in Raid controller, there are performance parameters that may be disabled by default; like write-cache to prevent data loss in case of power outage.
If is a Dell Raid card the Raid software that comes with the card allows you, from within windows, to modify the Raid array and set the array with write-cache enabled.
If the Raid 0 is properly set with disk write-cache enabled, and with two 15K 73GB drives you should see performance north of 130MB/sec.
Also keep in mind that 15K drives require active cooling, and if they are installed in a computer drive cage without proper cooling, the drives will reach critical operating temperatures within a short period, and can corrupt data, affect performance, and ultimately end the life of the drive prematurely.
The raid card installed on my 380 is Adaptec 39320A and the scsi drives are Seagate Cheetah 15k.4. The raid card is made for a PCI-X slot, but since the 380 doesn't have any PCI-X slots, it is installed into a 32bit PCI slot. Of course, I enabled the write cache of the raid setting with 64k stripe size.
And, I don't worry about the hdd cooling, because the drives were preinstalled by Dell. If the drives would be damaged due to overheat, Dell should take the responsibility of improper hdd cooling.
I have the same card installed in the 670 (PCI-X) and the my drives are in a forced air external enclosure. I have two Raid 0 setups in one of the card’s channel, the drives are 80 pin interface:
2 Seagate 147GB 15K.4
Two Fujitsu MAU 147GB 15K
I get an average between 140-170/mb/s in transfer rates.
It could be that the regular PCI slot is being saturated by the U320 interface. You could do a test and go to the cards BIOS and manually change the max transfer rate of the drives installed to U160 and see it the Raid transfer rate improves, if it does, it means the system is trying to lock a u320 transfer rate, and if unable you may get poor results. When you force the card to lock the max transfer at U160 it may negotiate a higher MB/s transfer rate.
Also the reason for the cooling on the drives is not so much that Dell installed them, and that they could be replaced under warranty. The issue is that Raid 0 or even used as regular drives, the data has no redundancy; no data mirror is being made as in case of Raid 1.
If the drives reach critical operating temperature over a period of time, you may turn on the computer on one day, and the drives may not respond, and all your data will be lost; if not backup exist.
I’ve done several repairs on systems with 10K & 15K in the drive cage and a few months the drives stop responding due to heat damage, all the data in the drives gone; regardless if they were used as Raid or regular drives; and Dell is not responsible for loss of data.
Message Edited by Chipstone on 07-16-2005 05:33 PM
I changed the max transfer rate to 160 MB/s as you suggested, and did a test again. But, there were no improvements on the number, just 78~80MB/s. I also suspect the 16bit PCI slot restricts the transfer rate. If so, what should I do draw out the best scsi raid performance on my 380? My 380 has only three PCI slots and three PCI-express slots(16x, 8x, 1x).
This time, I'm disappointed with Dell. They advertised in their website that they provide an option of U320 15k scsi drives for precision 380, even though 380 is not designed to take advantage of the full performance of the scsi drives with its PCI slots. They are not honest at least in their advertisements. I'm not sure I can recommend Dell products for others next time.
It would possibly be a bug of the card. But, it seems nobody in Dell recognizes the problem as a bug. The current firmware is the latest one
Like you, I tested the performance on XP 64bit edition, not a trial version but a DELL OEM. I didn't test it on other Windows version, so I'm not sure this problem is a Windows issue.
I would like to exchange my scsi card and drives with SATA drives, but the DELL can't do that. The only way is to return the 380 and reorder, which is not possible for some reason.
I've read your posts and the replies regarding the slow performance of your hard drives. I too may be in the same situation, because I've just ordered the workstation 380 with the exact same configuration... (2) 73GB, 15K RPM, SCSI drives with the Ultra 320 (model 39320A - I guess?) controller in a RAID 0 configuration (it's in production as of this writing).
If you don't mind, please share with me and others, the results of your latest efforts to speed things up. Have you been successful? Or are you still disappointed and at a standstill with Dell?
I would appreciate your reply and of course, I will gladly let you know the average disk transfer rate of my system when it comes in.
I regret that you've had the difficulties with your new system that you've had - it is ridiculous that Dell would put a hot controller designed for PCI-X in a slower PCI-standard bus. It's poor business practice and doesn't make any sense.
First of all, if I were you, I'd like to cancel the order and reorder with two 10k SATA hdds in
raid 0 setting instead of SCSI hdds. You can save the money and get a faster storage. Of course, I know the advantages of using SCSI hdds, but you will hardly find them with 380.
There are no changes on my situation: 80MB/s transfer rate for two 15k hdds in raid 0 setting and the same even in single drive setting. This is really strange.
I talked to Dell tech support in Korea several times, but they always placed the responsibility on the Adaptec controller. They never agreed that it was a problem of bad 380 design. So, I gave up finding a solution from them, and am considering to give up using raid 0 and go to single drive setting.
If you insist on SCSI hdds, you'd better contact the Dell support and make sure the problem I have will not happen in your 380. Maybe dell support guys in US would be smarter than those in Korea.
If you have any tests to do before cancelling, tell me. Then I'll test it for you and let you know the result before you receive your one.
Chipstone
525 Posts
519
0
Posted July 16th, 2005 10:00
If is a Dell Raid card the Raid software that comes with the card allows you, from within windows, to modify the Raid array and set the array with write-cache enabled.
If the Raid 0 is properly set with disk write-cache enabled, and with two 15K 73GB drives you should see performance north of 130MB/sec.
Also keep in mind that 15K drives require active cooling, and if they are installed in a computer drive cage without proper cooling, the drives will reach critical operating temperatures within a short period, and can corrupt data, affect performance, and ultimately end the life of the drive prematurely.