I've done something that left my 32GB SSD drive showing up as the E: Drive. Now there is no Accelerate Tab. I'm running Windows 8. Any help would be greatly appreciated. I somehow think I don't have the drives set as RAID, and I don't know how to set that.
Here is the applicable portions from the Dell Support Center test
I need some more information like if you upgraded Windows 8 through Windows 7 or if you did clean installation of windows 8 operating system through a DVD. Also let me know if you did any changes to the BIOS settings before installing/ upgrading Windows 8.
Windows 8 will have to be installed or upgraded in a specific way for the systems shipped with mSATA. Let us know the way you have installed or upgraded to Windows 8, so that we can assist you in resolving the issue.
I installed Windows 8 through Windows 7 (i.e., I did not do a clean install of Windows 8). After I received my computer, I made a Restore disk and then installed Windows 8 through Windows 7.
Hi sdouglas77, The Acceleration mode has to be disabled in the Operating system before installing or upgrading to Windows 8. Since Windows 8 is insalled without disabling the Acceleration mode, same has to be manually disabled. I suggest that you follow the below given steps to disable the same:
Boot to Bios (F2)
Change Sata operation to AHCI
Save settings and Exit
As soon as the system boots up tap the F8 key to go into Advanced options
Choose option Repair my computer
Wait for 3 – 5 minutes on the black screen until the system shows up recovery options
On System Recovery option click next
On user name / password option click next (if password has been set for primary user please enter the right password)
On System Recovery Option screen ------> Select Command Prompt
At Command prompt type in Diskpart
Type LIST DISKà You should see 2 Disks listed like below
Note down the right DISK number for the next steps. On some systems Msata HDD would be either Disk 1 or Disk 0
DISK ###
Status
Size
Free
Dyn
GPT
DISK 0
Online
29 GB
19 GB
DISK 1
Online
465 GB
5091 MB
Type SELECT DISK 0(Whichever is msata drive)
It should say DISK 0 is selected
Type Clean
This should clean the msata HDD
Type OFFLINE Disk
This should make the Disk Offline
DISK ###
Status
Size
Free
Dyn
GPT
DISK 0
Offline
29 GB
19 GB
DISK 1
Online
465 GB
5091 MB
Type EXIT
RESTART
On Restart go into BIOS (F2) and change SATA back to Intel Smart Response Technology
Thanks so much for the detailed instructions. However, I cannot get the Advanced Options screen. F8 simply doesn't get me there. I tried rebooting at least 25 times. Tried hitting F8 in all sorts of ways - tapping, once, holding it, repeating it. I tried SHIFT-F8 (which brought up diagnostics). Nothing will get me to the advanced options.
My apologies for asking you to press the F8 key to go to the Advanced Boot option windows. As you informed F8 key does not work in Windows 8 Operating system.
Bring up ‘Charm Bar’ and click on ‘Change PC Settings’. Select ‘General’ from the left Panel and scroll down to the bottom of the right panel, click ‘Restart Now’ under ‘Advanced Start up’. In the next screen click on ‘Troubleshoot’ which will bring the ‘Advanced boot options’ windows. Please click on ‘Command Prompt’ and proceed further as per the steps provided in the previous post.
Thanks again. However, I can't boot to Windows after I change the SATA to AHCI. The only way it will boot to Windows is by selecting IRST. I tried the COMMAND PROMPT while in IRST. However, it wouldn't take the MSATA drive off line. When I type "OFFLINE" it just gives an explanation of what the OFFLINE and ONLINE means, and when I type LIST DISK, it shows both ONLINE.
Again, I really appreciate all the time you're taking.
In AHCI mode you will be unable to boot to the Operating System but you should be able to go to ‘Advanced Boot Options’ menu. In case you are unable to go ‘Advanced Boot Options’, let me know the screen the system is going to or also check if there is any error message.
When I boot in ACHI, it sends me into the "Preparing for Automatic Repair" or something like that. It goes through diagnostics, and finally kicks me out into a "RESTORE" option. If I hit RESTORE, the system locks up. If I hit, CANCEL, the system reboots and locks up. The only way out is to go back to the Boot Options (F2), and change it back to IRST. Then it boots normally.
Nonetheless, at some point during one of the many reboots and command prompt attempts, something happened. This morning, I clicked on IRST (while I was in Windows), and the ACCELERATE tab appeared. I clicked on it and it now shows that the C drive is accelerated using the MSATA drive.
Does this mean it's accelerated? It seems to boot fairly fast now, but I can't say for certain that it boots faster than before.
When it shows that the C drive is accelerated using the mSATA drive, means the mSATA drive is configured, I also suggest that you flash BIOS to the latest version by clicking on the link below:
Select the model of the system, then the Operating system and click on BIOS and flash to the latest version. While flashing BIOS, do not use the system till it restarts and comes up to the desktop and please have the Ac adapter connected to the system as this needs uninterrupted power supply.
DELL-Sujatha K
Community Manager
•
3318 Posts
•
15 Points
1290
0
Posted November 20th, 2012 03:00
Hi sdouglas77,
I need some more information like if you upgraded Windows 8 through Windows 7 or if you did clean installation of windows 8 operating system through a DVD. Also let me know if you did any changes to the BIOS settings before installing/ upgrading Windows 8.
Windows 8 will have to be installed or upgraded in a specific way for the systems shipped with mSATA. Let us know the way you have installed or upgraded to Windows 8, so that we can assist you in resolving the issue.