UNSOLVED

mikesnowball

updated

19 years ago

0

4138

January 28th, 2008 00:00

Hard Drive Failure

I have a Dimension 8400 running XP Professional using raid 0 with two 160 GB serial ATA WDXL-80 hard drives.  One has failed.  When I run the hard drive diagnostic I get a Return Code: 7.  I seem to remember seening an article on this and that it was not a complete failure.  What steps do I need to take to get it back running?
  • PETER345

    1 Rookie

    •

    5796 Posts

    230

    0

    Posted January 28th, 2008 00:00

    Can you put it in another machine as a slave? Then you can try reading your data and to repair the damage if it is just a bad sector.

    Peter
  • 230

    0

    Posted January 28th, 2008 01:00

    The other desktop I can use doesn't have a raid configuration but I will give it a try.
  • PETER345

    1 Rookie

    •

    5796 Posts

    230

    0

    Posted January 28th, 2008 01:00

    This is part of a RAID array? If RAID 0 (striping), don't bother, you can't read the drives independently. For RAID 1, you should be able to read each drive independently.

    Also, if it is RAID 1 (mirrored), then you don't need to be so careful about data loss because each drive is a copy of the other.

    I'm not sure if there are any tools to repair a drive when operating as part of RAID.

    Many would warn you not to keep using a drive that has developed problems, but that is up to you to decide.

    Peter
  • 230

    0

    Posted January 28th, 2008 22:00

    I intend to replace the drive.  There are a couple of emails that I wanted to get off of it first.
  • 230

    0

    Posted February 3rd, 2008 17:00

    I ran the boot utility and got the following message during the read test Error Code 0F00:0244 Msg block 74123808 Uncorrectable data error or write protected media.  Is there a way to isolate this block?  All the other tests passed; verify, write, smart, etc.
  • PETER345

    1 Rookie

    •

    5796 Posts

    230

    0

    Posted February 3rd, 2008 18:00

    If by isolate, you mean to make sure it is not used, then, yes, you can do that with chkdsk "Scan For and attempt recovery of bad sectors".

    If you mean something else, then I'm not sure.

    Peter
  • 230

    0

    Posted February 5th, 2008 20:00

    Is there a way to run chkdisk without the ability to boot the computer?  With the one bad drive I can't boot up.  When I try booting to a command prompt I can't typing anything in.
  • PETER345

    1 Rookie

    •

    5796 Posts

    230

    0

    Posted February 5th, 2008 21:00

    Sounds like you have two problems.  You can run scandisk by booting to the recovery console on the Windows install CD (command prompt), but you have to be able to type the command.

    You can also move the drive to another machine as a slave or external drive and check it there.

    Peter
  • 230

    0

    Posted February 7th, 2008 00:00

     

    Thanks for your help.  I think I have come to the end of the line for trying to recover any data.  I installed two new hard drives and will add the one good one from the first two as soon as I get the necessary cabling.  It was frustrating to see that the drive was not completely bad and not be able to recover anything from it.  I won't use the Raid 0 configuration anymore.  The speed benefits are not worth the reliability risks.

  • PETER345

    1 Rookie

    •

    5796 Posts

    33

    0

    Posted February 7th, 2008 01:00

    I agree with you.  With RAID 0, it seems you need to do backups religiously.

    Peter