Okay I have this reallly big problem here. When I start my computer it works fine and can read every CD/DVD I put in. But then just suddenly, at some random time, it won't react at all.
Under "My Computer" it also dissappears, just suddenly it seems like my computer doesnt register it anymore. And if I have a DVD/CD inside it and try to eject, it wont react. Also the light indicating activity on it, is on all the time when it doesnt react.
so..what's wrong?
Message Edited by Computer092 on 12-03-2005 09:07 PM
When you installed the drive, did you jumper it as Cable Select? Dell uses the Cable Select feature.
Does the drive show in the Device Manager? Is there an Error Code? If is goes missing in the Device Manager, make sure the drive is enabled in the Set-up (BIOS).
Dell uses the Cable Select feature. When two devices are jumpered as Cable Select, the position on the IDE cable determines the Master and Slave, thus, the cable selects. The device on the end of the IDE cable is the Master and the device in the middle is the Slave. I recommend jumpering both devices as Cable Select.
When the devices disappear in the Device Manager, it may mean there is a problem in the Set-up (BIOS). It could be a poor connection of the IDE cable at one of the drives or at the motherboard. Enter the Set-up and check that the drives are there and ensure the Secondary IDE Channel 0 and 1 are enabled to turned ON. If one of the channels is OFF, it can cause what you are seeing.
I did set the old DVD-reader to primary (master), and I set the new NEC DVD-writer to slave (on the same cable).
Both the DVD-reader and the DVD-writer is displayed in the device manager, but when they dissappear, they dissappear from the device manager. (By 'They' I mean that both the DVD-writer and the DVD-reader dissappears)
Also, I dont get any error messages, they just dissappear.
I dont quite understand if the Cable Select Feature would make any difference, cuz both drives are registered by the system when the computer starts. Everything works fine until a certain time, when they suddenly just dissappears.
Message Edited by Computer092 on 12-03-2005 10:44 PM
So you mean I should put both devices to cable select? Cable select is the thing in the middle of the jumper, right?
Also, the system I use (Dimension 4550) is pretty old, so are you sure the old ones like mine uses Cable Select?
Message Edited by Computer092 on 12-04-2005 01:34 PM
The thing is that when my computer starts up, everything works fine.
But then suddenly, at a random time, my new DVD-writer stops reacting, and it dissappears from the 'Device Manager' and 'My Computer'. When the DVD-writer dissappears, the DVD-reader also does.
So the thing is, both the DVD-writer and DVD-reader works fine until a certain random time, when they suddenly stop responding, and nothing happens when I press eject. The rest of the computer works fine all the time.
Message Edited by Computer092 on 12-04-2005 10:58 PM
It sounds like the classic case of IDE device confusion on the IDE chhannel. Cable Select will remove any confusion. Jumper the drives as Cable Select and lets go from there and see if there is a real problem.
Hello, me too have problem with 2nd writer--NEC I just installed that was set as slave.
Dell 3100 recognized both NEC 3550A (Firmware 1.06) & LG4164B but it took 55 min to write (TDK 8X DVD+R, Nero Express 7.0 ) instead of 18 min with just LG4164B by itself.
The buffer level jumped from 85%~17% during writing session...
I put in a spare writer : I/O Magic, same thing...changed jumbers on both to CS (Cable Select) as suggested here, 2nd writer just disappeared. ( the end cable is hooked up to LG4164B while the middle is to NEC 3550A) I even tried setting LG4164B as Slave and NEC3550A as Master, the PC just got confused and mixed up the ID on both.
I have another Clone PC with NEC 3540A as a slave writer which was just plug n go with no such problem. PLS help..Haven't been able to do any work since last night...
Skybird
1 Rookie
•
10871 Posts
633
0
Posted December 3rd, 2005 18:00
uses the Cable Select feature.
Does the drive show in the Device Manager? Is there an Error Code? If
is goes missing in the Device Manager, make sure the drive is enabled in
the Set-up (BIOS).