UNSOLVED

rhantson

updated

19 years ago

R

rhantson

3 Posts

0

9237

July 24th, 2007 22:00

3100cn & 3000cn Web Admin Interface Problem

Greetings Forum Members...
 
I've been fighting with this problem for about 3 weeks now, and am about to take these two printers to the dumpster because they are now completely and utterly useless on our network.
 
I've searched the forums here, applied every "idea" to reset the ADMIN password to the web interface, to no avail.  I've reset the NVRAM - no luck - even after rebooting.  I tried upgrading the firmware, and although the firmware update tool says "SUCCESS" the firmware is still sitting at:
 
General:
Firmware Version: 200611021450
 
Network:
Firmware Version: 6.38
 
I've done this on BOTH the 3100cn and the 3000cn, to no avail.  Has ANYONE successfully upgraded the FIRMWARE and/or been able to RESET the admin password on either of these two printers?  I've emailed our rep's at DELL several times, and they seem to ignore any emails from us unless we are asking for quotes. 
 
Solutions attempted thus far:
Firmware Upgrade - tools says success, printer remains the same
NVRAM Reset - Rebooted after, no change in any settings on the printer
Manual - Yes, read it back to back, probably have the thing memorized by now. 
 
 
 
  • 335

    0

    Posted July 26th, 2007 19:00

    Have you tried clearing the nvram through the web interface or on the panel?  I have had similar problems before where I thought I had cleared it and then suddenly it had the ip address again.  If you clear through the web interface, sometimes you have to say apply and sometimes you have to say restart to apply settings.  In the web interface, it's under 'Printer settings', 'Printer Maintenance', and then 'init NVRAM'.  Good-luck!
  • ThatRenGuy

    18 Posts

    335

    0

    Posted July 27th, 2007 14:00

     

    printerqueen42 wrote:
    it's under 'Printer settings', 'Printer Maintenance', and then 'init NVRAM'. 
    Wrong!
     
    There are 2 chips of NV memory in the printer, and I believe you've been resetting the wrong one. One is on the main system board, holding all paper tray settings and most other settings, and the other is on the network card, which is where that password is held.
     
    To reset the network card go to menu > configure > network (instead of maintenance) > init NVRAM
  • rhantson

    3 Posts

    335

    0

    Posted July 27th, 2007 15:00

    That Did It Folks!
     
    Resetting the NVRam in the Configure - Network area of the printer did the trick, we were finally able to get the printer setup on the network and it's running!
     
    Finally - a real answer to the problem!!!!
     
    Thank you!!!  Thank You!!!  and again...  did I say THANK YOU!?
  • ThatRenGuy

    18 Posts

    335

    0

    Posted July 27th, 2007 18:00

    My pleasure.
     
    These are great printers, they're just not the most user friendly design...
  • 335

    0

    Posted July 28th, 2007 15:00

    Sorry for the misinformation: Thanks for pointing out the difference in the settings. That's why when I clear the nvram for the network settings on the panel,it works; and when I do it through the web interface like I mentioned, it doesn't. Thanks again for clearing that up for us all. I'm a printer technician who's learning about these printers by on the job experience (like most of us I'm sure); so the things I happen to figure Out I like to pass on if they can help someone else. have a good day all:) P.S. Like if you take the two screws off both ends of the imaging drum (carefully of course), you can dump a whole lot of toner out into a garbage can and prolong the life of your drum. Otherwise you have to get a new one between 11000 and 20000 pages if you print in color much (instead of only black). They may be good printers, but dell has a way to make you keep on paying for those consumables if you don't practice a trick or two. Let's hear it for good old American ingenuity!