BlackSesame

updated

6 years ago

0

155442

January 24th, 2013 15:00

MD3200i locked down after change all hard disks

Our company has a new MD3200i with two 600GB drives. I had updated firmware and NVSRAM to the newest version. We had those two drives in RAID 1 mode. This week we got other 12 2tb drives, so I took out existing two drives and installed the 12 new drives. After I installed new drives, the array lost connection with Storage Manger software. After I reboot the array, I can connect it with the management IP address, but it is showing Storage Array Unknown and status showing Needs Attention. When I try to start "Manage Storage Array", all I got is Recovery Guru window showing Storage Array in Recovery Mode. I tried to quite the Recovery Mode through command line, but it shows following message:

"Unable to execute command. The RAID controller module is currently in locked-down mode because the firmware version on the RAID controller module does not match the version expected by the storage array's configuration database. Available commands include:

 

show storageArray healthStatus; or

download storageArray firmware file=filename [downgrade=true/false];"

I need help to troubleshoot this problem. Maybe I need to clear the configuration database, but I don't know how.

Thank you very much for any help.

 

  • 5551

    1

    Posted January 25th, 2013 13:00

    I called Dell support this morning and solved the problem by console in and reset the controller. Thank you!

  • DELL-Sam L

    Community Manager

    •

    8149 Posts

    •

    34712 Points

    5551

    0

    Posted January 24th, 2013 16:00

    Hello BlackSesame,

    The config for your Raid 1 was on the 2X600GB drives that is why you are getting the message that the array is in recovery mode.  What you will need to do is to either put the 2 drives back in the MD3200i and then import the config & it will bring the raid1 back as long as you haven’t formatted the 2x600GB drives.  If you have formatted the drives then you will have to setup the MD all over again.  When you setup the MD the first time & update the firmware it takes into account how many drives are in the unit and are there any extra enclosures attached. 

    To clear the current config on the MD you need to run the following command: clear storageArray configuration (all | diskGroups)

    You can also check out the SMCLI guide & on page146 it walks you through how to clear the config.  ftp://ftp.dell.com/Manuals/Common/powervault-md3200_reference%20guide_en-us.pdf

    Please let us know if you have any other questions.

  • 5551

    0

    Posted January 24th, 2013 17:00

    Sorry I need to be more clear. I tried "clear storageArray configuration all" command, but still get same error message.

  • 5551

    0

    Posted January 24th, 2013 17:00

    Thank you for help. But I got same message saying it is in locked-down mode because mismatch firmware version.

  • DELL-Sam L

    Community Manager

    •

    8149 Posts

    •

    34712 Points

    5551

    0

    Posted January 24th, 2013 18:00

    Hello BlackSesame,

    It looks like you configured your MD with security on the drives that prevents them from being put into a different MD & reading the data.  what you are going to need to do is that you should have created a key to use so that it can remove the lock that is on the system.  If you did create a key then you can remove the lock on the unit.  Here is a link to the admin guide & on page 80 it explains how to do it.   ftp://ftp.dell.com/Manuals/Common/powervault-md3660i_Administrator%20Guide_en-us.pdf

    If you didn’t create the key then I would open a support case so that they can reset the system for you.

    Please let us know if you have any other questions.

  • Libi

    12 Posts

    5551

    0

    Posted July 13th, 2013 12:00

    Hi,

    i have the same issue here with a MD3200.

    Both controllers are in lockdown mode.

    Please help me to clear configuration and reset the controller.

    Alex

  • Dev Mgr

    6 Operator

    •

    9308 Posts

    •

    3 Points

    5551

    0

    Posted July 13th, 2013 18:00

    Those steps are probably not documented and probably aren't allowed to be posted (here on Dell's forums).

    I'd suggest you open a case with support like BlackSesame did.

  • DELL-DavidB

    1 Message

    5551

    1

    Posted July 19th, 2013 05:00

    Just had today in Tech Support a case like described (MD3200 in lock down mode) .

    I confirm you need to call Tech Support to receive assistance.

    I'm afraid that this information is not documented as instructions are available only for Tech Support.

    Please have on hand the serial cable to connect to the controller (s).

    Notice that, depending on the configuration,  replacing or taking out some disks in a row,  -and for sure all of them- can cause the controllers to lock down and of course data lost.

    L2 Prosupport Server&Storage

    Get Support on Twitter: @DellCaresPro @DellAyudaPro

  • 2352

    0

    Posted November 23rd, 2020 06:00

    Hello, I have the same problem.
    Can you help me?

  • DellEMCSupport

    1 Rookie

    •

    631 Posts

    786

    0

    Posted November 23rd, 2020 09:00

    Hello AndreW9955478,

    Which MD system do you have?  What is your current lockdown state?