Have followed some of the posts regarding installing NT 4.0 Server on a PowerEdge 1600SC, but have not been able to successfully install the OS. After installing the RAID driver, I still get a "hard disk not found" message. I am attempting to install using boot floppies ...
I am having exactly the same problem, installing nt4 onto a 1600.
i install nt from fresh and then install the raid controller drivers after pressing s and it picks up the drivers for the perc 3 but then still says cannot find hard drives...
This guide should help out with your "no hard drives" message:
NT 4.0 Installation Guide: Boot to your Microsoft Windows NT 4.0 CD. When the message "Setup is now inspecting your hardware configuration" appears, press [F6].
NOTE: When the first blue screen appears, you have approximately 1 second to press [F6]. The next message must say "Setup was unable to detect ..." If not you did not press F6 fast enough.
If a PERC is present, perform steps A-B below. If a PERC is not present, perform step B only: A. Press to specify additional devices, select Other, insert your PERC disk, and then follow the prompts to install the drivers. B. Press again, select Other, insert your SCSI driver diskette, then follow the prompts to install the drivers.
Continue with the installation using the on-screen prompts as a guide, while noting the following important considerations:
** When installing device drivers, always click Have Disk, if given the option. NEVER allow NT to search for devices, as doing so may result in a corrupt installation.
** When you choose the role of the server (PDC, BDC or Stand Alone) keep in mind that you cannot go from Stand Alone to Domain Controller or vice-versa after the install is complete, so make sure that you know what the proper role of your server is before specifying it.
** Do not install video drivers until Service Pack 3, or later version, has been installed.
NT 4.0 is not validated on the PowerEdge 1600 SC. Microsoft is dropping support for NT 4.0, therefore new systems are no longer allowed to be validated, however it may be possible to install using alternate drivers.
This driver is for the PowerEdge 2600, but it has a similar Scsi controller.
LSI Logic U-320 SCSI Driver, Nt 4.0, PowerEdge 2600, v. 1.08.04, A01 Filename: 22320-nt10804a01.exe [52 KB]
I bought a PowerEge 1600SC and I want to install Windows NT4.0. I need the scsi driver. Where can I get it?
Can I Install Windows NT 4.0 on PowerEge 1600SC?
It appears you are in the Asia / Pacific region of the world. I do not have access to the details of your system configuration. Do you have a Raid Controller installed? If so, which model? Do you have Scsi or IDE hard drives?
With this information, I can advise which driver you need to load using this NT 4.0 Installation Guide:
Boot to your Microsoft Windows NT 4.0 CD. When the message "Setup is now inspecting your hardware configuration" appears, press [F6].
NOTE: When the first blue screen appears, you have approximately 1 second to press [F6]. The next message must say "Setup was unable to detect any mass storage devices..." If not you did not press F6 fast enough.
If a PERC is present, perform steps A-B below. If a PERC is not present, perform step B only: A. Press to specify additional devices, select Other, insert your PERC disk, and then follow the prompts to install the drivers. B. Press again, select Other, insert your SCSI driver diskette, then follow the prompts to install the drivers.
Continue with the installation using the on-screen prompts as a guide, while noting the following important considerations:
** When installing device drivers, always click Have Disk, if given the option. NEVER allow NT to search for devices, as doing so may result in a corrupt installation.
** When you choose the role of the server (PDC, BDC or Stand Alone) keep in mind that you cannot go from Stand Alone to Domain Controller or vice-versa after the install is complete, so make sure that you know what the proper role of your server is before specifying it.
** Do not install video drivers until Service Pack 3, or later version, has been installed.
TAG:GHXBV0J
am having a similar problem to the previous,Firstly I need to add Poweredge 1600SC (W2K server pre-install) to an NT Domain and do not want to recreate user,groups etc.., been advised to overwrite W2K server with NT 4.0 server, configure as a BDC and then promote to PDC then upgrade to W2K server.
you mention drivers for HDD (I have 4 IDE's), which do I need for my set-up and do you know where I can get them
The "No Hard Drives found" message is indicative that NT 4.0 did not understand the IDE controller. If the size of the hard drive was an issue, the message would have been different.
This is the only solution I can think of: Boot to your Microsoft Windows NT 4.0 CD. When the message "Setup is now inspecting your hardware configuration" appears (still on the black screen), press [F6].
NOTE: When the first blue screen appears, you have approximately 1 second to press [F6]. The next message must say "Setup was unable to detect ..." If not you did not press F6 fast enough.
Press [S] to specify additional devices, scroll through the list, looking for the word ATAPI. I do not remember the exact name, but it is the only line with ATAPI in it.
Continue with the installation using the on-screen prompts as a guide.
ntsdq
2 Posts
414
0
Posted June 22nd, 2003 11:00
I am having exactly the same problem, installing nt4 onto a 1600.
i install nt from fresh and then install the raid controller drivers after pressing s and it picks up the drivers for the perc 3 but then still says cannot find hard drives...
What are we doing wrong??? Anybody???????