UNSOLVED

ykishan

updated

10 years ago

Y

ykishan

1 Rookie

•

12 Posts

0

2525

August 31st, 2016 16:00

pe 2900 replaced bad PERC 5/i controller. How to restore the VD configuration?

I got PCIe communication error, and after replacing the PERC 5/i controller, I see no configurations present for the controller. I tried to import foreign configuraiton, but getting error message. What is the procedure when someone needs to restore the previous configuration for the new controller. If I start new configuraiton, can it keep the existing data and is accessible to boot. Please advise. I see two disks in ready state and one disk in foreign state. Thanks

  • DELL-Chris H

    7 Practitioner

    •

    9682 Posts

    •

    48046 Points

    1711

    0

    Posted September 1st, 2016 07:00

    Ykishan,

    Before we try any of the following procedures, can you confirm the error you are seeing when you try to Import the Foreign? I ask as that is important to clarify before we proceed.

    The procedure you are needing is called a Retag. It is where you are recreating the Virtual Disk configuration, but you do NOT initialize the Virtual Disk as you normally would when creating a VD. As this will delete the data. Now with doing this you need to be 100% certain that you configure the Virtual Disk exactly as it was prior. 

    DELL-Chris H

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

  • ykishan

    1 Rookie

    •

    12 Posts

    1711

    0

    Posted September 1st, 2016 10:00

    Thank you very much Chris for quickly catching it with a brilliant answer.  As I mentioned, not all the disks are showing Foreign.  Only 1 out of 3 is foreign, and the other two are "ready" state.  When I go to "Foreign View", I see only 1 disk showing.  I am assuming since the other two disks are not foreign, it is not able to import. Currently I am not at server, and cannot give exact error message.  I will give exact error message later in the day.

    Also, i want to see if I can give a try by creating a new virtual disk attaching those 3 disks without initializing it, and see it can supply the vd for OS to boot up.  Just do not want to take any risk of loosing the data.  Another question is the new controller I got looks slightly different from the old damaged controller though both are DELL PERC 5/I.  Is it possible the new controller may not be honoring the old controller because of that difference.  Please note this was on raid 5 (3 disks each 70GB giving 140GB) came originally from DELL almost 10 years ago!  Thanks

  • ykishan

    1 Rookie

    •

    12 Posts

    1710

    0

    Posted September 1st, 2016 16:00

    Just checked again.  The error message I got when I try to import foreign config is:

    Error! Foreign Config Import

    1 out of 1 failied to import

    Error code: Unknown

    Looks like my only option is try recreating vd without initializing with raid 5 as it was configured before.  I can see old configuration under "Foreign View".  Question I have is if I do not initialize and try this way, even if it did not work, can I still keep the data intact so I can try other ways?  Please advise.  Thanks

  • DELL-Chris H

    7 Practitioner

    •

    9682 Posts

    •

    48046 Points

    1710

    0

    Posted September 2nd, 2016 07:00

    Can you confirm the part number for the original, as well as the new controller? Just so we can confirm they are compatible. With the retag, as long as nothing is Initialized then the information on the drives should remain intact. The retag will only change the configuration info on the drives, not the data itself. So if the retag fails you should still be able to send the drives to a data recovery company.

    If we are doing a retag, what i suggest is that you try clearing the foreign configuration, not import it. Do you see another error, all drives showing ready?

    If so then try the retag, remembering not to initialize the Virtual Disk, and let me know how it goes.

    DELL-Chris H

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

  • ykishan

    1 Rookie

    •

    12 Posts

    1710

    0

    Posted September 5th, 2016 19:00

    Thank you Chris for trying to help me with.  This is what I see as part number for the controller I got from Dell in 2006. 

    465-5028

    PERC 5/i, Integrated Controller Card

     UF963
    Just wondering if can still get this part from Dell. I will check with Dell tomorrow.  The one I tried the controller is "Dell PERC 5/i SAS SCSI RAID Card w/256MB Cache (PCI-E) - FF117 YF437 XM771 GT281"
    The one came with server does not have any memory attached, but the new one has.  I will check with Dell support tomorrow to see if they have this part available.  Also, I did not find a way to clear the foreign configuration.  Out of three, only one drive has foreign configuration. Other two are in ready state.  Thanks
  • DELL-Chris H

    7 Practitioner

    •

    9682 Posts

    •

    48046 Points

    1710

    0

    Posted September 6th, 2016 08:00

    I am not certain that the part will still be available. I would suggest contacting Spare Parts at 800-357-3355 and see if they still have in stock.

    Also, regarding the Foreign configuration, are you able to boot to the OS on this or is it failing? 

    DELL-Chris H

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

  • ykishan

    1 Rookie

    •

    12 Posts

    1710

    0

    Posted September 10th, 2016 17:00

    Thank you again for the help.  I am able to get the exact part from ebay.  After installing the exact part, now I am able to see all VDs and able to boot without any issue.  We need to use exact controller.