UNSOLVED

Ayush_raj_pal

updated

8 months ago

A

Ayush_raj_pal

1 Rookie

•

4 Posts

•

2 Points

0

388

March 25th, 2026 12:44

PowerEdge R740xd stuck at boot after RAID to HBA mode conversion - Metronome.efi crash

What I was trying to do: Convert drives from RAID mode to HBA (IT) mode for use with MAAS (Metal as a Service) provisioning. The goal is to have the controller in pass-through mode so the OS can see individual drives.

Steps taken:

  1. Entered PERC controller BIOS during boot
  2. Cleared foreign configurations on all drives
  3. For one server: Changed controller mode from RAID to HBA, scheduled for next reboot
  4. For other 3 servers: Manually converted individual drives from RAID to Non-RAID, then scheduled controller HBA mode for next reboot
  5. Rebooted all servers

The Problem: All 4 servers are now stuck at boot with the following error visible in iDRAC virtual console:




Additional symptoms:

  • Servers display "System has critical issues" on health check
  • Servers were attempting PXE boot (for MAAS) but now completely frozen
  • Cannot boot into OS or reach PXE
  • iDRAC is accessible, virtual console shows the above crash
  • Physical drives show as "Ready" or "Non-RAID" in iDRAC storage view

Hardware:

  • Dell PowerEdge R740xd
  • PERC H730P Mini (Embedded) - Firmware 25.5.7.0005
  • iDRAC9 - Firmware 7.00.00.183 (Enterprise license)
  • 12 x HDD drives (front) + 2 x drives (rear)
  • DELL-Erman O

    Moderator

    •

    2984 Posts

    •

    14874 Points

    0

    0

    Posted March 27th, 2026 13:08

    Hi,

    I thought its like the system crashes in UEFI (Metronome.efi / Avago SAS driver) before PXE or OS handoff, so everything appears “frozen”.

    Just an idea to quick fix:

    1. From iDRAC, switch the PERC back to RAID mode and cold power‑cycle (power off 30–60s).
    2. Boot F2 → System Setup, delete old UEFI boot entries.
    3. In Device Settings → PERC, clear all configs/foreign.
    4. Update BIOS, iDRAC, and PERC firmware.
    5. Reboot, then change to HBA mode only (don’t manually convert drives).

    After this, the system I would expect boots normally and PXE/MAAS works.

     

    Hope that works!

    DELL-Erman O

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

  • Ayush_raj_pal

    1 Rookie

    •

    4 Posts

    •

    2 Points

    0

    0

    Posted March 28th, 2026 10:01

    The current situation is that the PERC is still in the RAID mode and 10 disk are in NON-RAID mode and others are still in RAID mode...

    I can't even change the NON-RAID drives to RAID mode or anything else the server is frozen,

    I have 3 servers which are in the exactly same state(mentioned above)  
    and 1 server where all the drives are in NON-RAID mode but the PERC is still showing it self in the RIAD mode.




  • Ayush_raj_pal

    1 Rookie

    •

    4 Posts

    •

    2 Points

    0

    0

    Posted March 28th, 2026 10:18

    I even tried to spam F2 as soon as the Dell logo appear but the server is still not responding...

    is there any other way to enter system setup...?
    I just wanted to get my servers back in running state, even RAID mode is fine... :)

  • DELL-Joey C

    Moderator

    •

    4170 Posts

    •

    20965 Points

    0

    0

    Posted March 30th, 2026 00:15

    Hi, 

     

    To confirm if the issue is caused by the controller card or the drives, can you try removing them out from the server and try to turn on the server to access the BIOS. Then try installing just the controller card without drives. 

    DELL-Joey C

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’ if I did. 

  • Ayush_raj_pal

    1 Rookie

    •

    4 Posts

    •

    2 Points

    0

    0

    Posted March 30th, 2026 10:14

    Hello,

    As the servers are at the Data Centre, it is hard for me to do this,

    could you tell me a fix for this that will work 100%, as I won’t be able to go to the DC this often.

    Thanks!

  • DELL-Marco B

    Moderator

    •

    3980 Posts

    0

    0

    Posted March 30th, 2026 16:19

    Hello,
    Unfortunately, there is no fix that can be guaranteed to work 100% without physical troubleshooting. Hardware issues can only be isolated by testing components step by step. Without on-site checks, we can suggest best‑practice actions, but a 100% certain solution is not possible.
    Best regards,

    DELL- Marco B

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!