I cannot locate anything pertaining to the inlet temp sensor, or how to replace it. I was speculating that maybe it is either built into the right control panel, behind the fans, or built into the motherboard. I was curious if it was this DP/N: 095GHY
It would appear that 'maybe' this is the sensor attached to this cable for the housing of the USBA & USBC I/O, please correct me if I'm wrong.
The Inlet Temperature Sensor on your Dell PowerEdge R440 is integrated into the Right Control Panel (Right Rack Ear) assembly. Because it is permanently embedded on that tiny circuit board, the sensor cannot be replaced separately, and you must replace the entire right control panel piece.
D2PJF (or 0D2PJF): This is the correct part number for the Dell PowerEdge R440 Right Control Panel / Right Ear assembly with cable.
Before buying any parts, use your upcoming maintenance window to perform these specific isolation steps:
The "Flea Power" Drain:
Power down the server completely.
Disconnect both power supplies.
Hold down the physical power button on the front of the server for 15 to 20 seconds. This completely drains any residual electrical energy stored in the capacitors and forces the hardware controllers to deeply reboot.
Inspect and Reseat: Open the chassis and follow the ribbon cable from the right ear back to the motherboard. Unplug it, check for pin burns or tears, and firmly reseat it.
Check the Left Control Panel: On some 14th-generation Dell servers, the \(I^{2}C\) bus strings through the left control panel (which handles system health LEDs). Ensure the left panel cable is also snugly connected.
Firmware Verification: Ensure your iDRAC9 and BIOS firmware are up to date. Sometimes a corrupted firmware chip stops reading the bus properly, and a re-flash fixes it.
If you complete the flea power drain and cable reseat but the error returns immediately upon power-up, the sensor circuitry is permanently dead, and replacing the right control panel (D2PJF) will resolve the problem.
with kind regards Martin/ Liebe Grüße Martin
Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!
I have a Dell PowerEdge R440 server that is currently in production and the iDRAC is reporting a persistent Inlet Temperature Sensor failure.
The iDRAC shows:
System Inlet Temperature: Not Applicable
The following event is recorded in the System Event Log:
Log Sequence Number: 10711 “The sensor indicating the inlet temperature is not responding either because the sensor is damaged, or because of damaged circuit lines for I2C bus, or a faulty sensor state.”
The recommended action from the iDRAC is to reset the iDRAC and, if the problem persists, replace the corresponding I2C sensor.
I have already performed an iDRAC reset (Reboot iDRAC), but the problem persists. After the reset, the same Inlet Temperature Sensor error was generated again.
The server is otherwise operating normally. The cooling fans are working, but the iDRAC is reporting approximately 100% PWM fan speed.
There was also a previous event related to Fan 5, which was subsequently replaced. In addition, the server experienced several unexpected shutdowns due to prolonged power outages. The server is connected to a UPS, but on some occasions the UPS autonomy was exhausted and the server shut down unexpectedly.
My questions are:
Where exactly is the Inlet Temperature Sensor located on the PowerEdge R440?
Is the sensor integrated into the Right Control Panel / Right Rack Ear?
Can the sensor be replaced separately, or does the entire Right Control Panel assembly need to be replaced?
I have seen references to part numbers D2PJF and MJXTG. Which part number is the correct replacement for the R440?
Could the previous unexpected power losses have damaged the sensor or the I2C circuit?
Is there any additional diagnostic procedure I should perform before replacing the hardware?
I am planning a maintenance window to power off the server and inspect/reseat the Right Control Panel cable and connector.
DELL-Charles R
Moderator
•
4730 Posts
•
25476 Points
5
0
Posted June 17th, 2025 20:44
Hello,
The Right ear control panel does have the temp sensor.
These would be replacement part numbers for the cable to use:
Part #:D2PJF
Part Desc.:ASSY,LTCH,RACK,RT,1U,R440,V3
ASSY Latch Rack 1U, Right, Version 3, 1U
Part #:MJXTG
Part Desc.:ASSY,LTCH,RACK,RT,1U,R440,V2
ASSY Latch Rack 1U, Right, Version 2, 1U
Either will be ok to use.
DELL-Charles R
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Accept as Solution’. ‘Thumbs up’ the posts you like!