Latitude E6540 came stock with Intel Advanced-N 6235 (2x2) card (w/ Bluetooth 4.0). I don't NEED Bluetooth, so I want to change wireless cards to an Intel Ultimate-N 6300 (3x3) wireless card.
It SHOULD NOT be a BIOS wireless networking card white-list problem, as the Intel Ultimate-N 6300 is spec'd for some Latitude E6540 machines, and there is a DELL-supplied driver package for it.
I uninstalled (w/ delete drivers) the Intel Advanced-N 6235 and ProSet wireless; shut down and removed the card; cold rebooted to make sure everything was gone.
Installed the 6300 card, booted up and TRIED to install the Dell package... The package is giving me the following error:
Installation Blocked, This software package cannot be installed on your system. Please resolve these errors and retry installation.
You have done the right thing by uninstalling the driver before installing the new card. Please check if the installed new card is detected in the BIOS. Tap F2 at start up to open the BIOS screen. Navigate to General under Settings and click on it to expand. Next click on System information and scroll down and check what is listed for Wireless Device, if it is not listed, shut the system down and reseat the drive and check. Let me know the status.
Yes, of course. The card is in the BIOS Info screen... reads "Intel Wireless" just like the 6325 card did.
UPDATE: Tried and tried and tried to get the driver to install.... with the card in, out, while chanting ancient Indian prayers.... no go.
So I decided to go BACK to the stock card... reversed the process and tried to install the Dell 6325 and Bluetooth driver packages...
GUESS WHAT! The 6325 package gave me the SAME Installation Blocked message...
There's some kind of BS going on here... Some kind of locking the system down collusion between or among Dell or Intel... No reason for drivers to be BLOCKED...
Is this a whitelist issue? Is Dell physically blocking parts? What's going on?
I had to spend about 4 hours last night verifying and restoring disk image files to get my system back to a place where I could use it on wireless again....
I regret the inconvenience. Dell supports Intel Centrino N 6300 card on this system model. Therefore there is no question of blocking the replaced card.
I appreciate your technical expertise and good know the wireless is working now. I would like to know if the wireless is working with the old wireless card after restoring the system to the factory installed state.
If it is the old card on the system, I advise you to perform the same step of uninstalling the driver, and then replacing the old card and updating the driver. You may click on the below link to uninstall the driver:
First, let me apologize for the tone of my last response... I was really tired and frustrated, but that isn't an excuse. I will try to be more patient. :emotion-1:
STATUS:
1) Old card re-installed in system.
2) Final post setup-image restored to HDD.
3) System running normally (well not exactly normal, but that's a separate issue.... The Intel Diagnostics are throwing errors on the network wireless similar to: An Administrator Profile has failed to secure an IP address from the DHCP Server. This error continues IN SPITE of the fact that I have put Static IPs on all enabled adapters (wired, wireless, and bluetooth), and I have disabled both Microsoft Mini-port virtual wireless adapters).
Bottom Line, I am back at square one on the wireless...
A) I would LIKE to get the Intel Ultimate-N 6300 Wireless Card running on this system...
B) At some point in the future, I would like to be able to upgrade to the newest Intel Dual Band-AC 7260 + Bluetooth for Laptops card working on this E6540... even if is with a generic driver package... The 4th Gen processor et al. supports it, and it is a MUCH more capable wireless card, and I need the band-width over wireless to do my job with customers.
But, let's take it one step at a time...
So, are you asking me to try this again... IF so, here are the steps/order I propose to follow. Please advise if I am misinterpreting your instructions.
1) Put system on wired ethernet.
2) Uninstall the 6235 card with the Device manager and check the "remove drivers" option.
When you removed the Intel adapter and installed the Intel 6300, you removed the battery and pressed and held the power button for 30 seconds? This allows the computer to look for new hardware.
�
Download the drivers for the Intel 6300 from Intel Download Center and save them to your desktop.
�
Make a system restore point.
�
Start, control panel, device manager, network adapters, right click on the Intel adapters listed there, left click uninstall. Tell it to remove the drivers and software.
�
Restart your computer. When you log in, the new hardware wizard will try to install the drivers, if may work or may not. If it does not work, then install the drivers you saved to your desktop.
OK... I have tried this think about 10 different ways now.... restoring to a fresh image every time.
I used the Revo Uninstaller, too. It's a great product, but made no difference in the outcome.
I tried installing drivers before the card install and after card install.
I tried the Dell driver package, and two of the latest Intel Driver packages. None of them work.
The Dell package continues to display the "blocked" message I referred to originally.
The Intel 16.1.1 package APPEARS to install correctly, and the card installs with drivers and shows up in the Net Adapters window, but BOTH the Intel Diagnostics AND Windows do not REALLY see the card.... not bound...
The Intel 16.1.5 package looks like it installs correctly, but does not appear to have a driver for this particular card, because the adapter fails to find a driver and doesn't show up anywhere.
After all the regular ways of doing this were exhausted, I also tried SEVERAL different combinations using additional tools to try and clean up the registry and HDD... I used a combination of jv16 Power Tools, Spybot S&D Pro 2, Auslogics, BoostSpeed, and Windows built-in tools (including regedit).
I scrubbed the registry and the HDD the best way I know how... Made next to no difference...
And yes, I've been doing the battery and holding the power switch thing...
Some comments...
Dell's original installation of the ProSet Wireless package leaves an ENORMOUS amount of trash behind when it is uninstalled, including the ProSet Wireless Common stuff, and at least 4 different active Services, and an active process... primarily surrounding the iFramework.exe and the /Intel/Wireless/bin directories.
After 10 image restorations, and 28 total, including 12 straight, hours of punching this problem in the face, I am no closer to making the Intel Centrino Ultimate-N 6300 work now, than I was days ago.
And here is the screen shot of the failure to find/install a driver with the latest Intel driver package (16.1.5 for Win7 x64).
With the earlier Intel 16.1.1 package, the Device Manager screen, device configure, screen, et al. look "normal" as in they have all the expected services apparently bound to the adapter, but ProSet says no adapter is installed, and Windows shows "No connections available".
If the issue persists, please check the status in the Device manger and provide the screen shot of the Device manager with the Network adapter or other devices expanded.
DELL-Sujatha K
Community Manager
•
3319 Posts
•
18 Points
3378
0
Posted September 15th, 2013 03:00
Hi CAUTERY1,
You have done the right thing by uninstalling the driver before installing the new card. Please check if the installed new card is detected in the BIOS. Tap F2 at start up to open the BIOS screen. Navigate to General under Settings and click on it to expand. Next click on System information and scroll down and check what is listed for Wireless Device, if it is not listed, shut the system down and reseat the drive and check. Let me know the status.