UNSOLVED

123harry

updated

23 years ago

1

123harry

3 Posts

0

126604

July 28th, 2003 23:00

Intel PRO/1000 MT network card in GX260 constantly disconnects and connects

I have an Optiplex GX260 running Windows XP with all the latest updates and patches. The network card drivers are from Intel version 7.036.0.

The nic constantly connects then reconnects. I have tried manually setting both the switch (Cisco Catalyst 3500XL) and the network card to autoenegotiation, 100MBFull and 100Mb/Half, all to no avail.

 

It only works at 10/Mbps Half or Full, which is pretty useless.

Anybody seen this before or know of a solution?

Thanks.

  • DELL-Cody

    2 Intern

    •

    2166 Posts

    1219

    0

    Posted July 29th, 2003 13:00

    Ensure that the port used on the switch to connect the Optiplex system is configured for PortFast, or that Spanning Tree is disabled for that port.
  • droid256

    73 Posts

    1219

    0

    Posted July 29th, 2003 14:00

    That is a technical term called flapping.  We had some early model Cisco 3500 XL switches that experienced that problem with every gigabit NIC we tested.  Cisco eventually admitted to the problem and replaced all of our 3500 XLswitches.



    Here is the show version information from our failing switches:



    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 00:07:EB:95:40:C0
    Motherboard assembly number: 73-3904-12
    Power supply part number: 34-0851-02
    Motherboard serial number: Removed
    Power supply serial number: Removed
    Model revision number: A0
    Motherboard revision number: A0
    Model number: WS-C3524-XL-EN
    System serial number: FAB0545U3SB
    Configuration register is 0xF

    Our new working switches are Model Revision # S0.



    Droid

  • 123harry

    3 Posts

    1219

    0

    Posted July 29th, 2003 21:00

    Thanks droid256,

     

    I dug a bit further and found a few references to the Cisco firmware revision about A0. My switch does have the A0 revision so I guess that is the problem. Is there a firmware upgrade or does the whole switch need to be replaced?

  • droid256

    73 Posts

    1219

    0

    Posted July 30th, 2003 13:00

    Cisco replace our switches.

    Droid

  • ccclub

    1 Message

    1219

    0

    Posted July 31st, 2003 02:00

    I am struggling with this too.  Anyone at Dell listening?  we have about 20 systems with these symptoms, driving us crazy
  • droid256

    73 Posts

    1219

    0

    Posted July 31st, 2003 13:00

    Have you tried talking to Cisco?
  • Griff76

    13 Posts

    1219

    0

    Posted August 4th, 2003 15:00

    If your Cisco 3500's are A0/A0 like Droid said, it's the switch.  We are fighting the same issue.  I am trying to get cisco to replace all 90 of our switches, but they're still acting like they know nothing about it.
  • MBarry

    1 Message

    1219

    0

    Posted August 8th, 2003 13:00

    We have similar problems with Extreme Switches. So maybe it is just not Cisco? Maybe there is something wrong with the NIC or drivers?

    MB
  • beta2

    6 Posts

    1205

    0

    Posted August 12th, 2003 12:00

    This seems to be an ongoing problem for many users of the Intel Pro/1000 MT NIC embedded on Dell's motherboards.  After extensive testing and configuring of our clients switch (not a Cisco) and their NICs, the issue was isolated to the NIC.  The chip that Dell uses from Intel is greatly modified from the original Intel chip for that NIC.  

    Our solution:  We disabled the ethernet controller in the BIOS and replaced the NICS with (any brand)standalone PCI NICS.

    The performance has been absolutely flawless.  While being a major supporter of Dell equipment, the embedded Intel Pro/1000 MT created to many conflicts for us to recommend its usage.

  • Griff76

    13 Posts

    584

    0

    Posted August 12th, 2003 17:00

    Beta,  What you experienced may be the case sometimes.  In our situation, the Cisco 3500s in question will not connect to any gigabit card at anything but 10 meg.   We have tried standard Intel Pro/1000 add-ons, and even tried to interconnect the 3500 to a Cisco 2950 switch.  Both of those failed.