UNSOLVED

atiltman

updated

22 years ago

A

atiltman

3 Posts

0

9062

April 24th, 2003 13:00

Blown 3C920? (plugged in phone line by accident)

Hey,

 

Erm, I cant seem to find any information on other people doing the same thing which is rather strange considering how easy it is to do.

On my Inspiron 8200 I accidentally in a tired stupor plugged the phone line into the ethernet socket on my laptop... after a few attempts at dialing I realised my mistake but it was too late? Since then my onboard nic has failed to function correctly. Its recognised by the system, passes all tests, detects the network speed, lights up.... sends packets. But wont recieve packets (indicated by my hub/lights on nic/hub and XP nic properties).

Sure, most people I work with just suggested buying a pcmcia nic... but I'm one of those people who cant handle knowing theres one built in thats not working properly. I dont understand how the 50v phone line could of blown the ethernet card/circuitry when the 50v was sent into the two centre pins (blue/whiteblue) which are POE (Power Over Ethernet), technically those pinn's should not be connected to anything and simply be shorted out or grounded as with most other ethernet devices not ment to utilise POE. (design fault???!!!)

I was just curious if anyone else had seen it and knows a quick fix? I dont have the guts to rip apart my Inspiron (now out of warranty) and sniff around unless I know what has to be done (which transistor/resistor(s) to replace?).

 

Any help or direction, pointers, hints, schematics or... anything would by greatly appreciated! ;)

 

Cheers in advance,

-Andrew

  • johnallg

    2 Intern

    •

    7280 Posts

    247

    0

    Posted April 24th, 2003 15:00

    50V would definately take out components.  I'd say interface circuitry and not the 3C920 chip was damaged.  Look for parts off the connector (trace the circuitry).

    You didn't state your model, so go to this link and select your notebook, then the Removing and Replacing Parts link.
    http://support.dell.com/us/en/docs/index.asp?cc=12&ct=86

  • atiltman

    3 Posts

    247

    0

    Posted April 25th, 2003 01:00

    I didnt state my model? from what I can see I did? an "Inspiron 8200": P4 1.6ghz, 256Mb ram, 20gb hdd, 3C920 10/100NIC, V92 Modem, 15" SXGA+, DVD/CDROM.

    The 3c920 is built into the system board, I dont quite understand how any components could of been blown when those pins should never of been connected to anything in the first place?

    From what I can tell if its not simply a transistor or a resistor that has been overloaded I am screwed and would need to replace the system board.

     

    Thanks for the info

    Message Edited by atiltman on 04-24-2003 09:13 PM

  • johnallg

    2 Intern

    •

    7280 Posts

    247

    0

    Posted April 25th, 2003 02:00

    Sorry, you did indeed state multiple times it was an 8200 - I read way too many posts in a day.  My appologies.

    The chip is on the motherboard and the RJ-45 connector on the side of the notebook is also connected to that chip, or the network connection would never work.  Plugging the phoneline into the RJ-45 would put the 50V dc phoneline voltage into the motherboard.  If it took the line offhook, the voltage could go up as high as 150v, depending on the phone system.

    Here is how to get to the motherboard:
    http://docs.us.dell.com/docs/systems/ins8200/remove.htm#1084976 
    system board: http://docs.us.dell.com/docs/systems/ins8200/sysboard.htm#1084976

  • cholula

    1 Message

    247

    0

    Posted April 26th, 2003 23:00

    have seen this done many times; however only a few have resulted in damaged hardware.  The most common problem is the damage done to the pins themselves.  RJ-45 wall sockets are designed to use both RJ-45 and RJ-11 ends, however, the nic on your computer is not designed for this and and RJ-11 can bend pins 2,3,6,7 to the side where they do not contact; if this is the case use a small needle to straighten them.

  • atiltman

    3 Posts

    247

    0

    Posted April 27th, 2003 11:00

    Thanks but that was the very first thing I checked after the initial panic (3 mins after doing it).

    No bents pins :(

  • WhisperPntr

    14 Posts

    247

    0

    Posted December 6th, 2004 22:00

    I believe i have done the same thing and am curious if there are any alternatives or fixes....