UNSOLVED

mattcowger

updated

23 years ago

M

mattcowger

2582 Posts

0

23680

February 18th, 2004 02:00

802.11g Card Hacking HOWTO

802.11g miniHOWTO

OK, theres a lot of people asking what the easiest way to get 802.11g into their laptop without paying Dell etc. This isn't the EASIEST way, but its probably the cheapest. You will need:

1 Netgear WG311 54 Mbps Wireless PCI adapter ($40 @ compusa)
1 Soldering iron
Skills to use said soldering iron
Willingness to possibly break your laptop.


DISCLAIMER: I AM NOT RESPONSIBLE FOR YOU BREAKING YOUR STUFF!

1) The crux of all this is the fact that the above mentioned card (the WG311) is nothing more than a MiniPCI (the kind of wireless card your laptop takes) in soldered onto a PCI card. First, you need to melt the 3 solder points that hold the yellow cover off of the back of the PCB. Remove the cover.

2) Unfortunately, netgear soldered the MiniPCI clips onto the MiniPCI card (probably to prevent people from doing this). You will need to melt these solder points very carefully to loosen them up, and pull away the clips. Be careful not to dislodge or burn any of the components.

3) Install th card into your MiniPCI laptop (i8600 for example).

4) Install latest drivers and firmware. Be happy with your new Atheros 5212 chipset card that supports winderful things like Linux, BSD, 108MBit (in theory).
  • Mandrake99

    139 Posts

    274

    0

    Posted February 18th, 2004 06:00

    Does this mini pci card have the antenna connections that will match the ones like on the truemobile 1300 that plug right to the card?

    mandrake99

  • mattcowger

    2582 Posts

    274

    0

    Posted February 18th, 2004 14:00

    This card does have that connector - its called a U.FL or Hiroshi connector (often used in Japan and the US for GPS devices). It only has 1 connector though, for the main antenna, not two for the aux and main antennas like the TrueMobile cards do. This could have an effect on performance, however I think that effect is far outshined by the fact that this is a 100mW output power card where the TrueMobile is a 31mW card.

    --m
  • jmwills

    2 Intern

    •

    11984 Posts

    274

    0

    Posted February 18th, 2004 19:00

    Hack (re-engineer) your card and void the warranty.
  • mattcowger

    2582 Posts

    274

    0

    Posted February 18th, 2004 19:00

    Sorry, I should have made that clear:

    YES, DOING THIS TO YOUR CARD WILL VOID ITS WARRANTY.

    I was willing to do this because)

    a) I felt I had the experience with electronics, soldering and other equipment to do it
    b) I was willing to lose the $35 for the card if it broke.
  • glenhead

    138 Posts

    275

    0

    Posted February 18th, 2004 20:00

    Umm...

    Not to be overly simplistic, and not to disparage someone's desire to sniff solder fumes (one of the greatest joys in this old propellerhead's life, fer sher), but why not go to eBay and buy a Truemobile 1300 for $40-45 including shipping?  There's one listed right now for $32.97 plus $8 shipping, and there are a total of 24 listed from $14 to $39.

  • mattcowger

    2582 Posts

    275

    0

    Posted February 18th, 2004 20:00

    Good questions.

    1) Hack value. its just fun to sniff solder.
    2) This card uses the Atheros chipset, and therefore supports the 108mbit Atheros extensions. Since my router does as well, this is a good thing. The Dell's do not support this.
    3) This is a 100mW card. The Dells are 32 mW cards. More mW = more power = more range.
  • mattcowger

    2582 Posts

    275

    0

    Posted February 18th, 2004 20:00

    Oh wait, sorry, that was my response for the other boards...how's this.


    WHO THE HECK ARE TO TO QUESTION ME? I AM THE GOD OF NETWORKING! BOWBEFORE ME PEON!


    heh.
  • Mandrake99

    139 Posts

    275

    0

    Posted February 18th, 2004 20:00

    With 3X the mW even with just the primary ant. makes good sense if your willing to put out a little effort.. I seriously considering the mod. As an automation / robotics tech I smell solder fumes every day. My Blitzz cardbus just ain't cuttin the mustard... dropout... dropout...

     

  • glenhead

    138 Posts

    275

    0

    Posted February 18th, 2004 20:00

    Hmmm...

    A well-reasoned response, stated intelligently.

    Are you sure you belong here? 

    Now, before anyone else gets his/her knickers in a knot, I'm only kidding.

    Thanks for giving me something to ponder, mattcowger.

    Glen
    i8500
    2.2GHz P4m
    512Mb RAM
    Radeon m9000

    Eschew misoneism.

  • mattcowger

    2582 Posts

    335

    0

    Posted February 18th, 2004 21:00

    You're right, you also need to worry about RECEIVING a signal as well. My understanding is that the Netgear WG624 router uses the exact same MiniPCI card internally...I have the router as well, and is rated for 100mW, so that helps on that side.

    Anything that uses the Atheros 5212 chipset should be able to do 108MBit....the Dlinks and the Netgears support.