UNSOLVED

storm121

updated

12 years ago

S

storm121

1 Rookie

•

20 Posts

0

14969

January 7th, 2015 07:00

Dell PC3448P / Sonicwall NSA220

Posted this over at Spiceworks as well.

Looking for suggestions on how to setup the following between a Dell PowerConnect 3448P switch and a Sonicwall NSA220.

We are switching over to a hosted phone system, using the Polycom 335 phones.

I purchased a dedicated POE switch for the phones only, PC3448P.

I've setup the Sonicwall NSA220 to use X4 interface from the switch.

I've setup the Sonicwall NSA220 to provide DHCP to X4 interface, for the phones.

This will all work just fine if I choose not to add another connection to my main network switch to manage the switch. When I do that, the phones try to get an IP address from my main DHCP server, which I do dot want. So I decided to try setting up vlans on the switch where the phones and sonicwall plug into.

I used ports 13 to 24 for the phones and Sonicwall, created a new vlan 100 and assigned those ports to them.

On port 13, I have a connection to/from the sonicwall x4 interface.

I currently only have one of the news phones on port 24.

With this setup, I have a connection from the POE switch port 1 to my main network switch, that port is on the default vlan 1.

So, with that, I have both the phone and the connection up to interface X4 on the sonicwall within the vlan 100 ports.

However, with the connection from the POE switch port 1 to my main network switch, the phone is getting an IP address from my main network DHCP server, and not the Sonicwall.

I ran across this site, could this be causing my issue?

http://www.bauer-power.net/2013/06/how-to-change-default-vlan-on-dell.html#.VK01_3s2V6A

  • DELL-Josh Cr

    Community Manager

    •

    9798 Posts

    •

    45341 Points

    834

    0

    Posted January 7th, 2015 11:00

    Hi,

    Is it configuration like this?

    Computers are on VLAN 1 using ports 1-12 and connect to a DHCP server

    Phones are on VLAN 100 using ports 13-24 and use the DHCP server on the NSA

     

    Does the phone system use tagged or untagged traffic? If it uses untagged traffic the ports should be in access mode and set on VLAN 100. It sounds like it can see the untagged traffic from the DHCP server and that is why it is getting an IP address from there. Are the DHCP server ip ranges different and not on the same subnet? You can try changing the PVID on the ports for the phones so they can’t see the DHCP server and only the NSA or you may need to create an ACL to block the DHCP server so they can’t see it.

  • storm121

    1 Rookie

    •

    20 Posts

    834

    0

    Posted January 7th, 2015 16:00

    Not to be redundant, but I posted a number of additional details over on the Spiceworks site here.

    http://community.spiceworks.com/topic/725821-dell-pc3448p-sonicwall-nsa220?page=1&source=homepage-feed#entry-4168375

    Not sure if your a member, but I think you can at least review the post.

    Still not sure of the switch is actually working correctly either.

    To answer some of your questions though.

    I have no idea of the phone system uses tagged or untagged, its a hosted solution, not in-house.

    DHCP servers are on separate devices and subnets.

    I have also opened a support ticket with Sonicwall to possible resolve the issue with it dropping request ober port 67 and 68 UDP, that may be the final issue, not sure yet.