I have been looking into 2 x 6224F to replace our 2 x 6024F switches, I am interested in the stacking features now that the units can support up to 24 static lags with the latest firmware. I have a question on how the stacking works and how much bandwidth the stacking modules deliver. The Dell web page claims the stacking module is upto 48Gbps but the interface is based on a HiGig+ 12 Gbps Physical Layer broadcomm chip that runs @ 12 Gbps not 48, are these units numbers based on using multiple cards in one stack? If you have two switches stacked together, do you only join one port between the two (XG1 on switch one to XG1 on switch 2) or can you join both ports at once (XG1 on switch one to XG1 on switch 2,XG2 on switch one to XG2 on switch 2) though by doing this I still can't see that it would give you 48Gbps per second (Maybe 24 Theoretically) or do you get to 48 as the stack grows?
Also if you utilize CX-4 or XFP modules can you place two of the ports in a lag to be able to link switches instead of the stacking modules.
I think you are correct about the 12 Gbps limit on each stack cable. I have a stack of two 6224s(non-f) that I just checked. Each switch has two module bays that can support two 10G connections on each bay. I believe that the 6224f has the same two bays. Each stacking module has two CX-4 style uplink connectors that are capable of 12 Gbps each. So I think theoretically if you fill both bays with stacking modules you can achieve the 48 Gbps stacking, but have no room left for 10 Gbps options since all bays would be full. Here is the output from my stack summary of two 6224s each has one stacking module with both uplinks connected between the switches.
Unit Interface ConfiguredStack-mode RunningStack-mode Link Status Link Speed (Gb/s)
1 1/xg1 Stack Stack Link Up 12
1 1/xg2 Stack Stack Link Up 12
1 1/xg3 Ethernet Ethernet Link Down 12
1 1/xg4 Ethernet Ethernet Link Down 12
2 2/xg1 Stack Stack Link Up 12
2 2/xg2 Stack Stack Link Up 12
2 2/xg3 Ethernet Ethernet Link Down 12
2 2/xg4 Ethernet Ethernet Link Down 12
So, I think I have a 24 Gbps stack.
I believe that you can use the CX-4 or XFP modules in a LAG and link switches, but you would not be able to manage them as a single switch and create other LAGs across them for redundant operation. It would also be slower (10G vs 12G), but they could be located physically farther away.
You can only place a stacking module in Bay 1 ( XG1 and XG2 )
Each stacking moduie supports 2 X 12Gbps full duplex connections - remember the stacking forms an active loop - so the total bandwidth is 12Gbps X 4 as each 12Gb channel can send and receive at the same time.
That makes more sense! I totally forgot about full duplex being counted in the bandwidth figures and that only bay 1 supports the stacking module. Here is a link to that manual page for more information if you need it.
stormytoad
44 Posts
237
0
Posted October 15th, 2008 15:00
Hi MS,
I think you are correct about the 12 Gbps limit on each stack cable. I have a stack of two 6224s(non-f) that I just checked. Each switch has two module bays that can support two 10G connections on each bay. I believe that the 6224f has the same two bays. Each stacking module has two CX-4 style uplink connectors that are capable of 12 Gbps each. So I think theoretically if you fill both bays with stacking modules you can achieve the 48 Gbps stacking, but have no room left for 10 Gbps options since all bays would be full. Here is the output from my stack summary of two 6224s each has one stacking module with both uplinks connected between the switches.
Unit Interface ConfiguredStack-mode RunningStack-mode Link Status Link Speed (Gb/s)
1 1/xg1 Stack Stack Link Up 12
1 1/xg2 Stack Stack Link Up 12
1 1/xg3 Ethernet Ethernet Link Down 12
1 1/xg4 Ethernet Ethernet Link Down 12
2 2/xg1 Stack Stack Link Up 12
2 2/xg2 Stack Stack Link Up 12
2 2/xg3 Ethernet Ethernet Link Down 12
2 2/xg4 Ethernet Ethernet Link Down 12
So, I think I have a 24 Gbps stack.
I believe that you can use the CX-4 or XFP modules in a LAG and link switches, but you would not be able to manage them as a single switch and create other LAGs across them for redundant operation. It would also be slower (10G vs 12G), but they could be located physically farther away.
Anyhow I hope this is helpful.