UNSOLVED

SteveS-ie8_8

updated

17 years ago

0

4365

January 15th, 2008 12:00

Cannot determine status of probe process - backup fails

If someone could help me with this one you would earn guru status. I have a call into EMC support but they have not been able to solve it.
One client is a new install of XP and has always failed with the following messages (in verbose savegrp mode):

"Cannot determine status of probe process. The log file is empty."
"Probe unexpectedly exited."

I have (sucessfully):
- turned all firewalls off
- uninstalled & reinstalled the client
- Checked client res/servers files for backup server name
- Checked name resolution (it's fine)
- rpcinfo -p reports nsrexec running (both ways, client & server)
- recreated the client entry in NMC
- client PATH env variable is good
- deleted the NSR Peer info

The network connection goes through one switch and the other clients backup fine.

I am at the end of my rope short of reformatting the drive and starting over.
Any other sane ideas?
  • 895

    0

    Posted January 15th, 2008 12:00

    Oh, and client initiated backups work although an index is not always written.
  • dk3

    163 Posts

    895

    0

    Posted January 17th, 2008 12:00

    Did you try to connect to XP Client on Networker's TCP Port 7937 with telnet or something? Did you try to use some network sniffer to see where your traffic is going to? Do you see any messages in daemon.log? I'm sure these questions have been asked by EMC already but you did not share much information :)
  • 895

    0

    Posted January 22nd, 2008 01:00

    - Are client and server in the same version ?
    - Have you test with a tracert Client to server , server to client that the route are the same ?
    Have try to use the hosts files only for the backup ?

    Have you check if your XP have disk full ?

    Try to run your nsrexecd in debug mode ( nsrexecd -D4 in a dos box) ...
    You maybe find a clue ...
  • 895

    0

    Posted January 23rd, 2008 08:00

    The client and server are the same version.
    I ran a trace route on both systems, pretty short path
    The disks are not full.
    Have run job with just the hosts file enrety (no DNS)
    No change on any of the above
    Did not sniff the wire. I will do that.
    Trying to run nsrexecd in debug mode. Can report that.

    Tried telnet to the port. Got some characters back but not sure what to expect.

    I did try running the savegrp from the server with this:
    savegrp -vvv -D9 -c client -G group
    There is a lot of info but comaring it to a good one shows this:
    Cannot determine status of probe process. The log file is empty.
    probe unexpectedly exited

    Nothing log wise on the client.

    I can run the savefs from the client and it works. (manual backup to the server).
  • legata

    3 Posts

    895

    0

    Posted January 23rd, 2008 10:00

    Did you try running a manually backup from the client side. If manually client backup is successful, and not successful from the server side? I suggest deleting the CFI. It is possible that you might have corrupted keys.
    Also, verify your DNS entry to resolve DNS.
  • ble1

    6 Operator

    •

    14354 Posts

    •

    56186 Points

    895

    0

    Posted January 27th, 2008 15:00

    Does it fail at save or savefs level? Also, since index is saved by server itself it may suggest issue in not on the box but rather server in index for that client. You could easily check that doing indexless backup (has to be set on pool level).
  • aduffy1

    1 Message

    895

    0

    Posted August 1st, 2008 06:00

    Steve, did you ever get an answer on this. I am having the same problem.
  • dgreggs1

    86 Posts

    895

    0

    Posted August 5th, 2008 09:00

    On the XP client check the NTFS permissions on the \nsr\applog and nsr\logs directories. Make sure Local SYSTEM has at least read/write on the directories and the files.

    Is the XP firewall turned off, at least for testing?
  • prsmail

    1 Message

    297

    0

    Posted August 18th, 2008 06:00

    Can u pelase check ur sevices.Networker service Logon Tab has to be starting with the Local Account.
  • 2dam

    85 Posts

    297

    0

    Posted November 11th, 2008 06:00

    Hi Guys,

    I am too having the same problem and have done the following:

    I have (sucessfully):
    - turned all firewalls off
    - uninstalled & reinstalled the client
    - Checked client res/servers files for backup server name
    - Checked name resolution (it's fine)
    - rpcinfo -p reports nsrexec running (both ways, client & server)
    - recreated the client entry in NMC
    - client PATH env variable is good
    - deleted the NSR Peer info
    - Checked that the nsrexecd service is started under the Local System account.
    - I have renamed the index folder for the client on the server to .old and tried again with a fresh folder but still no luck.

    Anyone found the answer?

    Thanks
    2dam