gsterle1

updated

21 years ago

G

gsterle1

10 Posts

0

1780

January 27th, 2006 12:00

ADIC Scalar i2K & Legato Networker - Config / modules required

I am implementing an ADIC i2k library soon and am interested in:
1. The specifications for the Legato Networker Server (make model, HBA's, mem, processors).Windows based (Intel / 2003 server)?

2.software required in addition to Networker 7.2 to backup SAN attached storage directly to the i2000 Disk to Tape on FC?

3. The i2K is FC attached to the SAN and the Legato Network Server is SAN attached (HBA). Can I backup other servers and possibly workstations that are not SAN attached to the i2000 server?

Any information or references would be appreciated.
  • brooks2

    12 Posts

    846

    0

    Posted February 16th, 2006 07:00

    I believe this means you have both HBAs zoned to see all the devices in the library. Zone the first HBA to the library and 3 drives, and the second to the remaing 3 drives. The I2k has the ability to control this also internally. You can configure the I2k to only present certain drives and the library to certain HBAs.

    -Brooks
  • ble1

    6 Operator

    •

    14354 Posts

    •

    56186 Points

    407

    1

    Posted January 27th, 2006 13:00

    ad 3) Yes - over the network.

    Will you have this library partitioned (multiple application sharing it) or will it be dedicated to NetWorker for backup?
  • DavidHampson

    2 Intern

    •

    1080 Posts

    407

    0

    Posted January 30th, 2006 04:00

    1. There has not been much documented about speccing a Networker server; however if you contact your EMC pre-sales contact they now have a sizing tool which is very useful. I have it on my laptop which I do not have a network connection for at present, but I am not too sure if it is something I am allowed to give out (plus there may be an updated version!) so contacting EMC may get it to you quicker.

    2. You should need no additional software to backup your data to the I2K. You will need to install the ADIC Management Console if you want to manage the library from a workstation rather than the front panel of the library, but this is not essential and will have no impact on Networker.

    3. If your workstations are not on the SAN then they will need to backup across the network via either the Networker server or a storage node. If you put the clients onto the SAN and wish to back up directly you will need to purchase Dedicated Storage Node and DDS licenses. If you have a large amount of data on a client this will probably be the preferable route unless you have a large backup window and/or gigabit ethernet.
  • ble1

    6 Operator

    •

    14354 Posts

    •

    56186 Points

    407

    0

    Posted January 30th, 2006 06:00

    The Library will be dedicated to Legato.

    Good - then you don't need any additional SW from Legato side).

    The Networker server will be SAN attached, (HBA's),
    therefore do I assume that Networker will see the
    Library?

    If your backup server and potential storage nodes will be zoned correctly yes.

    You mention storage node, can you explain exactly
    what a storage node is? Is that a separate server
    SAN attached?

    There 3 NetWorker components:
    - client
    - storage node
    - server

    In short:
    - Client is backing up and restoring data.
    - Storage nodes is managing drives/libraries.
    - Backup server is controlling all that plus makes metadata management.

    License you will need for storage node depends on your HW setup and general idea how you want this to setup. If yiu have basic setup where one box is server and controls all the drives than all licenses are already covered by the basic one.

    The DDS licenses and dedicated storage node. Do the
    DDS licenses get installed on the client or server?

    All licenses get installed on server (or license manager if installed and if in use).
  • gsterle1

    10 Posts

    407

    0

    Posted January 30th, 2006 06:00

    I appreciate the information.
    Follow-up:

    The Library will be dedicated to Legato.

    The Networker server will be SAN attached, (HBA's), therefore do I assume that Networker will see the Library?

    You mention storage node, can you explain exactly what a storage node is? Is that a separate server SAN attached?

    The DDS licenses and dedicated storage node. Do the DDS licenses get installed on the client or server?
  • DavidHampson

    2 Intern

    •

    1080 Posts

    407

    0

    Posted January 31st, 2006 03:00

    I haven't got a lot more to add from my initial response and what Hrvoje added afterwards. I would suggest you engage your EMC partner to discuss what you are trying to achieve in more details as it sounds like you probably need to define what you are hoping to achieve a little more closely and also so that you are happy that the licensing costs will fall within your budget.
  • mr7clean

    6 Posts

    407

    0

    Posted February 14th, 2006 13:00

    I am running the same setup and it works perfectly. Running over the network is just slower. Feel free to ask if you have any questions.
  • gsterle1

    10 Posts

    407

    0

    Posted February 15th, 2006 05:00

    The library is now installed. We are using QLogic HBA attached to a HP (brocade) SAN Switch. The Server sees the Tape Drives (Since the Server sees the drives I assume I have the HBA/FC portion of the task complete)

    However I am having problems with getting the Windows 2003E server to load the proper drivers for the following:

    1. Tape Drives - IBM ULTRAMUM _TD3 SCSI Sequential Device

    2. ADIC Scalar I2000 SCSI Array Device

    I can not seem to locate the proper drivers (except for the library).

    Am I overlooking the obvious / can someone direct me to the drivers for the Tape IBM LTO3 and (item 2.).
  • DavidHampson

    2 Intern

    •

    1080 Posts

    351

    0

    Posted February 15th, 2006 06:00

  • brooks2

    12 Posts

    408

    0

    Posted February 15th, 2006 08:00

    You don't actually need a driver for the Array Device, but I believe ADIC can provide you with one or at least a procedure so that it will stop prompting you to provide one.

    The IBM drivers you can get from IBM's site.

    A storage node would be a system connected to the SAN that would backup itself (dedicated) to SAN attached tape drives. There are other storage nodes which can backup LAN clients also, used to grow your environment when your networker server has a bottleneck (LAN, SAN, tape drives). DDS is used to share all or some of your tape drives in the I2k between the server and storage node, rather than having to split them up, 2 for the server, 2 for the node. Both systems can use any of the 4 drives, as long as they are not in use by the other. As mentioned, depending on your network, window, and client, I tend to make a dedicated storage node out of anything with over 100GB.