
Solved!
Go to SolutionClosed
U2711, OSD locked?
Hi,
My U2711 monitor OSD menu had locked out itself.
Self had tried as per instructions to hold button (4) for 15 seconds to unlock but that didnt work. The "LOCKED" symbol still stayed on the screen.
Self had tried the self-test; button (1) + (4) and the test works, hence button (4) is working too.
How do I do a hard reset to clear the firmware or reset the menu to original state and unlock?
Thanks in advance for any advice.
cheers..
1 person also has this problem
Responses (24)
Solutions (0)
Karmadillo
1 Message
4345
1
Posted April 7th, 2013 22:00
I had this problem with a Dell U2711 screen.
None of the above techniques worked. But then I stumbled upon a solution.
Solution
- Turn on a computer that is plugged into the currently selected screen input port (might require trial and error to work out which one).
- Press and hold lowest capacitive button for 15+ seconds.
- Screen stays on for the 15+ seconds required to unlock. Win.
What didn't work:
- Computers turned off.
- Pressing and holding lowest capacitive button for 15+ seconds.
- Pressing and holding lowest two capacitive buttons for 15+ seconds.
The screen would go into standby mode about 5 seconds into the process.
But this creates an opportunity to disable someone's screen: set it to an input that they do not have, e.g. DisplayPort; Lock the screen; They can't unlock it unless there is a signal coming in on the DisplayPort input.:emotion-3:
DELL-Chris M
Community Manager
•
56891 Posts
•
232143 Points
29784
0
Posted May 6th, 2011 15:00
armvalK,
* Power off the monitor
* Disconnect the power cord from the monitor
* Disconnect all monitor cords from the PC (USB, DVI, VGA, DisplayPort, HDMI, etc.)
* While disconnected, press and hold the monitor power button down for 5 seconds
* Reconnect the DVI cord to the monitor and to the PC video card
* Reconnect the power cord to the monitor
* Power on the monitor if it does not power on by itself
* Power on the PC
* Press the monitor Input Source Select button and choose DVI. Is it still locked?
DELL-Chris M (old account)
#IWork4Dell
Hi Chris,
Thanks for the guidance.
Have tried but all other buttons are of no response and button (5) when touched, a "LOCK" icon still shows on the screen.
The floating dialog box warning "DISPLAY PORT CABLE" still jumps around the screen.
However, I tried again holding button (4) and (5) for 15 seconds or so... and voila the touch button response returned and the OSD came alive.... whew...
OSD is unlocked now and input source select working...
There is a condition which may have caused this :
I am using Dell U2711 and U2411 side by side.
Dell U2411 is located on the right, which is jsut next to the U2711 touch-senstive buttons. So each time I observed that button (5) of U2711 is frequently lighted which indicates that its being "touched" by something. After awhile, the OSD of U2711 became locked... :(
---
guess i have to move the U2411 a little further away from U2711...
DELL-Chris M
Community Manager
•
56891 Posts
•
232143 Points
29771
0
Posted October 21st, 2011 08:00
tharlo,
What specific monitor model?
DELL-Chris M (old account)
#IWork4Dell
DELL-Chris M
Community Manager
•
56891 Posts
•
232143 Points
29770
0
Posted October 22nd, 2011 15:00
Ok. If my instructions below did not clear it, if under warranty Dell should replace it.
If you only have a Dell order number for your monitor, you should contact Order Support for your country. They will need the following data -
Email Address:
Name:
Shipping Address:
Phone Number:
Monitor Order number:
Monitor 20 digit PPID number:
Reason:
If your monitor was purchased tied to a Dell computer, contact Technical Support for your country. They will need the following data -
Email Address:
Name:
Shipping Address:
Phone Number:
PC Service Tag number:
Monitor 20 digit PPID number:
Reason:
DELL-Chris M (old account)
#IWork4Dell

JohanGreen
1 Message
29770
1
Posted March 16th, 2012 03:00
Hi found the solution to the pesky lock symbol on the net, thought I share it with you so the solution spreads :
Press and hold the two bottom buttons (4+5) for 15 seconds. the lock symbol will "unlock" after exactly 15 seconds and you are now able to use the OSD menu again! Funky part is that this is not mentioned in the Dell U2711 manuals (haven't been able to find anything about it).
JG
(edited)