
UNSOLVED
XPS M1730 Second Hard Drive Installation Help
Hi
I have a just over one year old (no warranty left) XPS M1730 laptop with Seagate 200GB 7200RPM drive.
Due to the space shortage, I've installed a second Samsung 500GB 5400RPM drive. Unfortunately, laptop BIOS does not see that drive and shows {none}
So, I switched the two drives by installing new Samsung at the Primary SATA0 and existing Seagate at the SATA1. This time, BIOS found the new drive with correct brand, size, and failed to see the existing Seagate drive.
I phoned Dell support to seek some help, and I was told that I have to replace the motherboard at Dell Or buy a new motherboard and install at your own high street local PC repair shop. As I do not have any warranty left, that solution is too expensive for me. Laptop is working absolutely fine apart from the space shortage.
I've seen some threads with similar story on this forum and I would like to know how they end up with their problems. Some say the SATA cable connector for second drive won't work unless you ordered the two drives spec laptop from Dell. My decision is I will not replace the motherboard just to get some extra place. But, I would like to try with a new SATA cable with two working connectors.
I would like to gamble by buying a new SATA cable to see whether the problem is at the motherboard or not. My current SATA cable might not have any circuit for the second connector. The big problem Dell spare part dept told me that they don't sell that cable.
Please somebody help me to solve this problem. Is it any software solution to enable the secondary drive or how/where can I buy a SATA cable with 2 (working) connectors?
Many thanks.
Responses (17)
Solutions (0)
Hi
Thank you again for your kind help.
I haven't see anything like that in the BIOS. It has a SATA Configuration under the Onboard Configuration. This is where you select RAID/Auto Detect RAID... and so on. I am at work and laptop is at home. Therefore, I cannot list out all the available command. If you know please tell me.
Thank you again.
CodeJackal
18 Posts
1710
0
Posted July 4th, 2009 01:00
I am watching this post .....I just tried to install a second X25-E in the available second bay in preparation for a dual boot Vista 64 and Windows 7 RC1 (X25 on Win7 to take advantage of the SSD defrag benefits) Now, I tried every configuration imaginable and I cannot get the two drives recognized on one OS. More specifically, if I have a single drive installed in either of the available slots, the notebook recognizes it. However, when I have both together in the notebook, neither is recognized....? I thought it could be the ribbon cable as well, but, I don't know.....I am still under warranty and will check with support to see what a solution is. I am glad I am not the only one. I can't live with only the X25-E as a standalone drive in the M1730 because it is only 32GB...., But I want the speed option available with the X25-E as a separate boot.....I reseated the drives multiple times, connected disconnected removed installed etc.......Can it be the ribbon cable? Or is it the MBoard?
CodeJackal
18 Posts
1710
0
Posted July 6th, 2009 10:00
I found more info outlined below in the article found HERE:
.......................”Here is a summary of what I have discovered. Normally there are three main options available for storage controllers: AHCI, RAID or IDE mode. Most people run IDE mode as this is the most compatible, and provides good performance. If selecting the AHCI mode, this choice needs to be made before installing Windows because switching between AHCI or IDE modes will usually result in boot failure with a BSOD.
AHCI's main benefit is that it fully utilizes SATA's advanced capabilities, resulting in more optimal operation, especially when the drive is multi-tasking. This means less drive noise, and less wear and tear for platter drives. A better explanation, and more importantly, a range of performance benchmarks, can be found in this article. Windows Vista and Windows 7 are the only OSes which natively support AHCI.
There are some quirks you should be aware of if you want to use AHCI. The first and most obvious is that as noted earlier, if you wish to enable AHCI, it is strongly recommended that you set it in your BIOS before installing Windows. If you insist on switching from IDE to AHCI on your current install, you'll need to use the method detailed in this Microsoft Article, and it's not without risk, so backup before doing it. The other issue is that you also need to install the Intel Matrix Storage Manager for AHCI to work properly on Intel motherboards. The Intel INF Chipset Utility which is necessary for all Intel chipset motherboards is not enough; the Matrix Storage Manager is not only for RAID setups, it also applies to single-disk AHCI setups as well. I admit I'd overlooked this step and had not examined the Matrix Storage Manager driver closely. Once I install the latest Intel Matrix Storage Manager I hope that everything will be fixed.”.....................
I’ll let you know what the result is when I make my second attempt at installing this drive to sit alongside the other platter drive.........
CodeJackal
18 Posts
667
0
Posted July 31st, 2009 18:00
No Luck installing the second SSD drive...... Never contacted Dell.....Both HDD from factory and X25-E if installed alone without any other drives installed work fine. I just cannot get them to work together......Any ideas anyone?....It may have something to do with the AHCI, but I do not think so.....When I did get both drives to be recognized in the bios, it did not want to boot, it acted as though the drives were in PIO mode and taking forever to startup. I mean hours....so I just gave up. Hopefully someone can figure this out.

ejn63
11 Legend
•
87469 Posts
•
321256 Points
1693
0
Posted April 23rd, 2009 05:00
Before you buy anything, did you enable the other drive in BIOS setup?